Jump to content
SAU Community

Recommended Posts

hi guys

wondering how long a stock r33 s2 turbo would last running 10-14psi before the turbo dies so to speak.

i know certain mods such as an after market ECU can run high boost, the mods i currently have on my dirty three are:

-greddy boost controller

-nismo full exhaust 3"

-k&n podfilter

-CENTRAL 20 ECU

-Greddy Front mount intercooler

also what probloms could occur?

cheers!

Link to comment
https://www.sau.com.au/forums/topic/335134-how-long-do-the-r33-s2-turbos-last/
Share on other sites

hi guys

wondering how long a stock r33 s2 turbo would last running 10-14psi before the turbo dies so to speak.

i know certain mods such as an after market ECU can run high boost, the mods i currently have on my dirty three are:

-greddy boost controller

-nismo full exhaust 3"

-k&n podfilter

-CENTRAL 20 ECU

-Greddy Front mount intercooler

also what probloms could occur?

cheers!

How long is a piece of string? it all depends on the condition of the turbo, and no car is the same. some people probably run 14psi+ everyday without dramas (yet) and yours could last a day. 14 psi is probably the limit of the turbo if you want to flow more, get it high flowed. then you wont be warrying everytime you hit boost.

^^^^haha krzsiu, you must have post as i was writing mine.

Edited by R3N3

If you pull the intake pipe off & check the wheel for side play then probably not much longer, Shaft play + 100,000rpm doesnt do good things to turbines, if there is no shaft play then the bearings are ok but still is a 20yr old turbo & things dont last forever-especially when boost gets wound up.

I replaced mine with a new steel wheel version cause I was paranoid it could let go with the new demands I am placing on the car-track work/skids/drags & a lot more boost. I thought better safe than sorry

ive been told some turbos nornally last till about 150,00km?

I got the car with 71,000 on the clock-which I rekon was BS-the timing belt had been changed & looked about 50,000 used(so more likely 140K, I have now got the odo at 187,000 & the turbo wouldnt have lasted much longer I think-nearly 2mm side to side in shaft-so may last may not-if your worried about it replace it is my advice or get it reconditioned-you must be getting close too like I was

1997 R33 GTST 228,000 with 0.85kgcm2 daily and aggressive tune

still have the standard turbo

lol troll? You should know better than to post something like that in a noob thread :D now everyone will swear their good for 200 thouusaannddd kms.

The answer truly is "how long is a piece of string".

Sure enough, if all conditions are PERFECT, it can possibly outlast the car itself. Yet when you take into consideration it is effected by SO MANY variables, its hard to put an actual lifespan on the item. One thing to note is that manufacturers GENERALLY put a 60,000km service interval on consumables (not including lubricants etc) and 100,000km on larger items.

How long is a piece of string? No one can tell you the answer to your question

Twice the distance from the middle to one end :D

The problems you will encounter with a blown turbo is...

No boost.

I have a S2 turbo and it has lasted more than a year of abuse on my RB20 at 14 psi. In the previous owners hands it was boosting to 18psi on a 20. Mine still feels good, minimal shaft movement.

Luck.

Give it one hard drive and the chances of blowing it are high. The boost dependent death is a heat related issue, not an age one. Meaning get it hot enough at any boost level and the rear wheel is sure to hit the housing. Once that happens you can look for the wheel in the cat.

im surprised mine is still going and hasnt killed itself

but ive always kept it at 0.85kgcm2 and never use a scramble/boost mode or run "high boost" etc

set and forget and a good decent tune

my 33 turbo has done 184,000km's, it whines a bit when im cruising off boost but still boosts nice. spose its luck of the draw lol. im replacing it with a R34 gt-t turbo soon so that should be a nice quiet change =P

  • 2 weeks later...
my 33 turbo has done 184,000km's, it whines a bit when im cruising off boost but still boosts nice. spose its luck of the draw lol. im replacing it with a R34 gt-t turbo soon so that should be a nice quiet change =P

ive noticed that mine has been whining for a few months now....not heaps but u can definately hear something. should i assume the turbo is nearly on its way out?? or does the whine only mean there could be a small amount of shaft play? no oil leaks or anything yet...

its a series 2 with 80,000km

Edited by normda

Technically the turbo is engineered to last the same amount of mileage as the actual engine in standard setup. I guess that doesn't work so well or there won't be any turbo re-builders.

how long do you last in bed? that varible changes from turbo to turbo man, depends on all sorts of other variables such as temperature, fuel mixture, how the car is driven, warm up, cool downs, air filter element used, fuel used... ra ra ra

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, this is probably where a wiring diagram and a multimeter come into play.
    • I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...