Jump to content
SAU Community

Need Full Car Sound/audio Installation


Recommended Posts

Hi guys, finally bought my FULL sound system (Sub/Amp/Mono/Front/Rears/) *hu alrdy installed* and need someone to install it.. will drop off my car aynwhere in melbourne.. aslong as they know what they're doing and are good on price..

names & numbers pleasee

thx

Hi guys, finally bought my FULL sound system (Sub/Amp/Mono/Front/Rears/) *hu alrdy installed* and need someone to install it.. will drop off my car aynwhere in melbourne.. aslong as they know what they're doing and are good on price..

names & numbers pleasee

thx

try jb they can do ok prices

they're the worst =\

AGREE!!!! got them to install a dvd head unit in my car and they stuffed it up big time...the headunit is not even put in properly and was shaking big time with every ditch on the road...had to take it out and mount it on the bracket myself properly...very annoyed at that...

:D

Anyway, just a FYI - SAU-Vic members get a super priced discount on Audio install.

You'd probably save more off the install then membership would cost

we get discounts from JB for audio installs? not bad but only if they can garantee a great job on it...never had any good experience from their installations...myself and some of the guys who got their sound system installed from them were not happy...but hey if you know someone working at JB and can give us a discount and is good at their job let us know so we can only to go to that store...

JB can do good low prices but there installs arnt the best. Known a couple of mates cars installs that had speakers held in by one screw :D. We were wondering what the rattling noise was and took it apart and there was 3 cars done like that. FreewayCarAudio Dandenongs a very good place to go. Bit more expensive but way worth it.

Depends where you go and who you get i guess. I've used JB (Epping) and Strathfield (Thomastown). Jb installed my front & rears plus pioneer dvd touch screen player and done a very nice job, everything was neat and professionally done. They do charge a little bit but thats the price you pay for not knowing how to do it yourself.

Strathfield on the other hand... they charge a lot and dont give a damn what their installations are like. They put in my sub & amp setup with the amp jammed in next to the battery,ripped the fuse box out from next to the battery as well and cables n shiit were everywhere. Not Good. Although i feel their service is a lot better than JB's.

Edited by sympozium7

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...