Jump to content
SAU Community

Recommended Posts

  • Replies 189
  • Created
  • Last Reply

Top Posters In This Topic

I should be in or at minimum pop round for a look see. I have it in my calander and will cash on the day if there are spots left or if anyone pops something later on in the day.

I should be in or at minimum pop round for a look see. I have it in my calander and will cash on the day if there are spots left or if anyone pops something later on in the day.

In the wife's Terror-tory again??? :D

lool bring afew spare afm's just incase :D :D

nah that engine is out, the blu 1 has a n/a in it now, but i have a rb26 s13 that i might bring but just wondering if it would be all good bringing a track car because last time everyone was in stock streeters

nah that engine is out, the blu 1 has a n/a in it now, but i have a rb26 s13 that i might bring but just wondering if it would be all good bringing a track car because last time everyone was in stock streeters

As long as it isn't too loud anything can enter :D

nah that engine is out, the blu 1 has a n/a in it now, but i have a rb26 s13 that i might bring but just wondering if it would be all good bringing a track car because last time everyone was in stock streeters

yea i was talking to your dad and he was saying you were going to put a na when the rego ran out, lol bring it along :D would be awesome to see how the 26 runs without a heavy skyline to lug around :D

isnt too loud ? i thought u skyline boys like the sexy loud noise of a 26 goin off ? if the 26 isnt ready i have a ca 180 i can bring. Anyone know where we can send forms so i can lock in my spot ?

It isn't us that mind the noise, it's the people in the housing near by :)

It isn't us that mind the noise, it's the people in the housing near by :ermm:

ah, pansies need to harden up. ill find out what car im bringing next week, prob be a ca 180 so wont b too noisy. Any news on where to send the forms ?

isnt too loud ? i thought u skyline boys like the sexy loud noise of a 26 goin off ? if the 26 isnt ready i have a ca 180 i can bring. Anyone know where we can send forms so i can lock in my spot ?

[email protected]

im in doof ill give u the forms monday

[email protected]

UPDATE : I AM COMING TO DO EPIC EPIC SKIDS IN THE AUTO lol

just thought i would though that in there lol

[email protected]

also has the fax number been amended yet?

Yes

believe it when i see it :P

Oi you, enter, send forms to [email protected]

Noise - the maximum vehicle noise emitted does not exceed 95dB(A) measured at

a point 30 metres from the track edge by approved measuring equipment.

From texi form last sept..

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...