Jump to content
SAU Community

Recommended Posts

okay first of all hi :)

two weeks ago i purchased a skyline, was sweet. still sweet

its a r34 25gt

yesterday i put unleaded 95 in it. . and today when i drove it there was a lot missfires. . D:

i dont know if its the fuel or rather the car is being dodgy

Edited by mynameisalan
Link to comment
https://www.sau.com.au/forums/topic/338967-r34-running-unleaded-95-no-go/
Share on other sites

drive very conservatively until you can use 98. If you have E85 around, squeeze some of that into the tank and dilute the 95. Around 10-15 litres will help, octane booster will also work if you get one that actually works.

on a NA 95 octane should be fine. any misfires on 95 won't be from the octane rating. might be from the quality of fuel, but not the octane. you could also try backing the timing off a bit if you are worried.

japan's octane ratings are the same as ours, they just happen to have one that is even higher, but they still have 91 and 95 octane fuels over there from what i gather.

  • 7 months later...

Geeze u guys do like if 95 is kerosene or some shit....

Where i'm from 95 premium is our best brew and we run all skylines on that with no probs...just keeping the boost down on hot days

i run e10 95 in the stagea and keep the boost to 5psi most the time and it runs fine

even on 7 psi its ok, down a bit of power compared to 98 but its fine

  • 2 weeks later...

japan's octane ratings are the same as ours, they just happen to have one that is even higher, but they still have 91 and 95 octane fuels over there from what i gather.

Yes, but the average altitude of Japan is about 1000m, whereas our average altitude is about 400m.

I believe the "knock" map on the standard ECU is designed for 95 octane.

Yes, but the average altitude of Japan is about 1000m, whereas our average altitude is about 400m.

What's the relevance of that on a MAFed engine?

i forgot to tell you guys that my spark plugs was the cause haha. running on 5 cylinders was fun.. NOT

95 is fine stuff but i still run 98 nowadays

Not trying to be rude, but a car down a cylinder sounds a lot worse than the odd backfire... How did you not notice?

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...