Jump to content
SAU Community

Recommended Posts

  • Replies 61
  • Created
  • Last Reply

Top Posters In This Topic

Yeah the r33 probably different cause mine hangs low and its put perfectly and note this was after I even modded the dump pipe higher to push the exhuast up as much as it goes and its still pretty low.

Curiously does anyone have a regu 92-z system? Wondering if these older systems have the silenced in the rear cannon as well. I believe this was the model preceding the 06 & r system

i'm sure the 92z do as well, but i dont know about the 96r. 96 is louder than 92, i'm not sure what the physical difference is between the two, it might just be a difference in terms of the size of the strictor, or that one has restrictor one doesnt

kakimoto states on their website that 06R is a hybrid of 92z and 96R + the titanium looking tip

but i was told that 06R is just 92Z with the ti look tip, the db rating on kakimoto's website is 93db for 06R, so it kind of makes sense, but i've never compared it before

Edited by chiksluvit
  • 2 weeks later...
  • 9 months later...

In regards to difference well when I took my car checked with the regu06 fitted when it still had the restrictor it was definately causeing a restriction it did not like the extra timing I had in my tune from my previous exhuast and it was pinging I havent had it put on dyno with no restrictor but in regards to how it feels certainly feels alot more responsive and free revs better and seems to boost better.

In terms of noise yes it did get alot louder as suppose to before its not quite as loud as my old one which was is a stright pipe exhuast with a cannon on the back but its still much louder than it was with the restrictor so that middle muffler on it doesnt do shit lol thats why they stuck a reducer in it.

Now I see why racepace wanted 3500 for a custom exhuast that would flow and be quiet cause its not possible to find one for cheap as this kakimato has shown.

any more updates?? any dyno time, worth doing?

does an oval resonator restrict flow over a hotdog type one? and what size dump pipe should be used with gt30's, does the flange support a 3inch only or could it go upto 4 inch?

Edited by SliverS2

Well without the restrictor the old timing that it had could be added back in was a difference of around 10 kw

what was the max power your car pulled with and without the restriction?

10kw from 300kw is actually not as bad as say 10kw from 200kw..

Edited by chiksluvit
  • 5 months later...

update: removed the restrictor out of the kaki regu today, definately is louder, havent driven at WOT yet as i wanna get it on a dyno to make sure its all good first

took some pics on the way incase someone is thinking of doing the same, took about 2hrs all up from removing the exhaust to re-fitting it, used a dremel to cut it out, the restrictor as mentioned is 2.5" and roughly 20cm long

th_806005b0.jpg

pic of the restrictor inside

th_3e7e8ba5.jpg

restrictor cut

th_4b559844.jpg

restrictor removed

th_381c633c.jpg

restrictor next to zorst

http://s234.photobucket.com/albums/ee47/bwrgtr/?action=view¤t=748ba40c.mp4

quick vid of the exhaust note, its got more growl in low revs, havent tested high revs yet

Edited by BWRGTR

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...