Jump to content
SAU Community

QLD Whoretown...

predator

By predator,
in Queensland

 Share

Recommended Posts

  • Replies 62.7k
  • Created
  • Last Reply

Top Posters In This Topic

  • chaos

    7164

  • Ska

    5791

  • BelGarion

    3645

  • Nexus9

    3590

Popular Days

Top Posters In This Topic

Popular Days

jlnewton Grand Master

jlnewton

Posted
Posted
i think the difference is.. with coilovers, the shock is actually welded to the bottom of the spring, and they are basically one unit and cannot be separated. Most things can be adjustable.  

With a spring and shock setup the springs and shocks can be separated and changed independently. In that setup you can adjust the shock, but not the actually spring height or anything like that.

Nah, people just use the term for the aftermarket adj one. My APEXi coilovers are identical to the standard ones except the spring seat is threaded and the adjustable shock rate knob at the bottom of the shock housing. Ohlins even use the same tapered spring like the stock springs.

predator Grand Master

predator

Posted
  • Author
Posted

jl: so you can actually remove the center to get it reconditioned with your springs?

I thought that was the reason why adjustable coilovers couldn't be reconditioned (one unit), whereas with a totally seperate coil and spring you can mix and match the spring and the actual shock absorber??

jlnewton Grand Master

jlnewton

Posted
Posted
jl: so you can actually remove the center to get it reconditioned with your springs?  

I thought that was the reason why adjustable coilovers couldn't be reconditioned (one unit), whereas with a totally seperate coil and spring you can mix and match the spring and the actual shock absorber??

I had mine reconditioned before I put them in and had the original Apex spring changed to king springs of custom rate to improve ride. Since then I have also changed the springs at the front myself. People don't recon them because they haven't seen that brand before. The Ohlin, Tein and HKS ones I have seen were all the same. Otherwise it would make changing the spring rates difficult, which would take away from there "racing" purpose. It took me 1.5hr to change the front springs on the R with the APEXi coilovers, from wheel off to wheel on.

These guys are one of the few that will reco almost any coilover:- http://www.shockreco.com.au/

predator Grand Master

predator

Posted
  • Author
Posted

ahhh.. cool i didn't know you could do that.

yep.. if i ever work on the handling of the 31 i'm going to try swap things myself to save labour costs. Generally just need a spring compressor don't you but otherwise its just bolts in and out?

predator Grand Master

predator

Posted
  • Author
Posted

those guys sound like a good group to keep in mind.

i was always wondering whether i could get my Zeals reco'ed as they are $4k suspension (apparently) but nobody knew of anywhere in melbourne that would touch them. Basically a few people said "just throw them out and buy something local"

jlnewton Grand Master

jlnewton

Posted
Posted
ahhh.. cool i didn't know you could do that.  

yep.. if i ever work on the handling of the 31 i'm going to try swap things myself to save labour costs. Generally just need a spring compressor don't you but otherwise its just bolts in and out?

Yeah, spring compressors are cheap and a one off expense, I got mine from Repco for about $50, they were the cheapest, but for what I want they are fine, I think supa cheap has them for even less. Its kinda fun doing it youself, playing with the spring rates in the R has been fun, have learnt heaps about how spring rates effect the handling, I think I have it about just right for 95% road use, 5% track use. I really like a nice handling car, it gives you so much more confidence, and make you look like you are a better driver than you are :) .

jlnewton Grand Master

jlnewton

Posted
Posted
those guys sound like a good group to keep in mind.  

i was always wondering whether i could get my Zeals reco'ed as they are $4k suspension (apparently) but nobody knew of anywhere in melbourne that would touch them. Basically a few people said "just throw them out and buy something local"

They are just too expensive to replace, they can do all sorts of things. I have been talking to him about re-valving the APEXi ones as I think they could do with a little more rebound control, they only need the unit for a day to do that for me. As long as the shock housing hasn't been damaged its all good.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • MBS206
      Chris' Toyota Mark ii JZX110

      By MBS206 · Posted

      I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • GTSBoy
      RB26DETT Sketchy boost mod?

      By GTSBoy · Posted

      Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...