Jump to content
SAU Community

Recommended Posts

Hi fellas,

I am planning on adding performance parts to my R33 GTR and was thinking of some oil coolers. I understand most people often add oil cooling units for either their transmission or engine to cool the oil in them. My question is, which would add some noticeable performance gains and would both be good?

Moreover, to get a few extra kilowatts of power - would larger injectors and an aftermarket fuel pump add anything. I'm currently running a stock engine with only performance coilpacks and spark plugs so would this add anything?

Cheers,

Link to comment
https://www.sau.com.au/forums/topic/344293-oil-cooler-vs-transmission-cooler/
Share on other sites

to my knowledge there are NO performance gains other then keeping the engine healthy and lowering high oil temps though track or industrial area abuse.

although lower oil temps could mean better turbo performance as they don't like high oil temps

to my knowledge there are NO performance gains other then keeping the engine healthy and lowering high oil temps though track or industrial area abuse.

although lower oil temps could mean better turbo performance as they don't like high oil temps

Thanks mate...

But should I get both oil coolers or just one for the engine?

Cheers.

thats one thing that i'm unsure on, if lower gearbox temps will make the gear box last longer and not blow/less likely to blow then i'd have one in yesterday, fairly easy on the rb20/25 as u just use the auto banjo bolts and hard line.

i've been meaning to ask if there's any real difference or can you still kill your box just as easy?

Kevin don't you just drive your car around on the street? What on earth would you need a tranny cooler for :)

You do realise the point of an oil cooler don't you? It is to keep the temps from climbing high which will cause engine oil to thin. Meaning unless you drive your car very hard on the streets, it aint going to be doing squat for you.

You have been on these forums for as long as I have and you ask a question such as "would larger injectors and an aftermarket fuel pump add anything"....

Edited by PM-R33
Kevin don't you just drive your car around on the street? What on earth would you need a tranny cooler for :)

You do realise the point of an oil cooler don't you? It is to keep the temps from climbing high which will cause engine oil to thin. Meaning unless you drive your car very hard on the streets, it aint going to be doing squat for you.

You have been on these forums for as long as I have and you ask a question such as "would larger injectors and an aftermarket fuel pump add anything"....

Thanks mate. I'm a noob - not going to try and deny that. :-)

Basically, I'm trying to add some extra power on my GTR but don't want to upgrade turbos as I find them very responsive. Wonder if there's anything else I can do...that's why I raised these questions... thanks mate.

injectors, pump, FPR, and a new wastegate spring, or a new wastegate all up, of anything a hks one. but thats HKS money.

with the 440cc injectors you would be limited to the 300kw mark, same as the stock pump i guess.

go for 550cc, tomei FPR, and either a HKS wastegate or a 1 bar spring/s for your ones now. then add a decent BOV that wont kill itself above 10psi.

there you go, that should pull you up to about 300kw at the fly.

thats assuming you have a decent exhaust fitted before all else, whats the point on putting in more if you cant remove of more.

You missed the main thing he needs if he wants more power, an ECU.

Basically if you want more power these are your steps for your 33 GTR:

1. Exhaust

2. Cam gears

3. Boost controller

4. ECU Tune

5. Clutch

He doesn't need an aftermarket FPR.

Kevin if you really don't know much about performance modifications start searching in the Forced Induction section. It has been covered MANY times. Or simply go see Trent or some one regarding a package he would recommend.

Edited by PM-R33

your way would be the proper way of doing it. like if you have alot of cash flying around, but then again, rb26 parts are getting hell of a lot cheaper than the rb25 parts.

my way was just replacing the ecu upgrade with a FPR, a hell of a lot cheaper. but then again, nowhere near as good as a ecu.

p.s, i also think the performance section would cover just about everything

Edited by Bronx
You missed the main thing he needs if he wants more power, an ECU.

Basically if you want more power these are your steps for your 33 GTR:

1. Exhaust

2. Cam gears

3. Boost controller

4. ECU Tune

5. Clutch

He doesn't need an aftermarket FPR.

Kevin if you really don't know much about performance modifications start searching in the Forced Induction section. It has been covered MANY times. Or simply go see Trent or some one regarding a package he would recommend.

^^ This!

But I would not push the stock turbos over 1 Bar (14.7 PSI) unless you have steel internals.

what if the car is auto? even on the street, autos benefit from a cooler once you increase the power. so keeping that in mind, auto trans cooler or engine oil cooler? both w thermostats of course

If your skyline has that tiny single-loop-of-pipe trans cooler then yes, I think in an australian climate its an important upgrade, even on a stock vehicle.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...