Jump to content
SAU Community

10 - 12" Sub In The Boot Feedback

Longz

By Longz,
in Car Audio & Electrical

 Share

Recommended Posts

Longz Mentor

Longz

Posted
Posted

So i was thinking of adding a Sub to my sound system i was concerned regarding the weight of it , do people with subs that big feel a difference when driving , can u feel a power difference due to it being in the car is what i am mainly asking.

Thanks feedback appreciated

Link to comment
https://www.sau.com.au/forums/topic/344979-10-12-sub-in-the-boot-feedback/
Share on other sites
89CAL Grand Master

89CAL

Posted
Posted

I feel mine roll around and smack into both sides cause its not bolted down lol

But honestly... Ive taken mine out to take the car down the strip. And the only thing I've noticed is my music doesnt sound as good. Its only say 5kg for a 12" sub and box, while if your looking for a complete stripped out track going car, is alot. Just your average performance road car its not a big deal. I really dont think you'd notice the difference anyway

Carbon 34 Grand Master

Carbon 34

Posted
Posted

you can build a carbon fibre or fiberglass box, tube, enclosure

or even get by with a smaller sub under the rear deck lip depending on the car model.

I find my car ride is better on the street with more weight on the rear but my spring rate is jap spec stiff, but I have extreme amounts of equipment and very large amounts of O gauge wire

I use carbon fibre and fiberglass in my car to cut the weight as much as possible, yes you notice it a bit but the spare weighs a lot more then both of my sub boxes

But your not driving a race car on the street, you need good tunes..lol

do a few mods to the engine and stop eating maccas and you over come the weight in the boot????..hahaha

and not having a box mounted is a disaster waiting to happen, dents or it turns into a missle in a accident ?

SKITTLES Experienced

SKITTLES

Posted
Posted (edited)
You can always get a slim line sub. . The new 1s from pioneer are pretty decent. You also end up with a nice clean install. . The cool thing about the slim line is you make it so that it is totaly hidden. .

AANNNDDD They sound like shit.

My mate just bought one, decent quality apparently, and I'm just like urgh. I've raped the shit out of my 12" clarion and it still sounds better than his. He turns it up, and you can hear it distort majorly (this is on the day he bought it, too). Where-as mines 6 months old, and still has better quality.

From a logistics POV it's not bad, however if you want quality, go a normal size.

I've got a 12" clarion in a 10" sub box. To bolt it down, I put some pine wood under the carpet and screwed it in. nice and ghetto. I'll get things fibreglassed when I have the dosh, but it's holding great atm.

I didn't feel a different in weight.

These are 6 cyl cars which weigh around 1.4tonnes, a 5-10kg sub, box and amp isn't going to make a great difference.

> and not having a box mounted is a disaster waiting to happen, dents or it turns into a missle in a accident ?

That, and it'll damage your cables.

>> Edit2

Also, just noticed you've got a GTR. dfw about weight. Go get a professional to carbon fibre or fibreglass a box in the boot for you. It's a beautiful car you've got, please don't do dodgy home jobs.

Edited by SKITTLES
PM-R33 Grand Master

PM-R33

Posted
Posted (edited)

Get a custom fibreglass moulded box for the side(s). Takes up dick all room and looks very neat.

http://shop.ebay.com.au/seductive.sounds/m...from=&_ipg=

Edited by PM-R33
Carbon 34 Grand Master

Carbon 34

Posted
Posted

you can fit a pair of 10 or 12 behind the factory panels on most skylines(most cars too), in a custom fibreglass box, they don't take any room at all, looks factory still. much better then the e'blow generic box.

I have a pair of pro 12's in a carbon fibre/bullet proof lexan bandpass box's and it takes up minimal room,(tuned to match the speaker not generic boxes ) still have full access to the spare etc. ported thru the factory speaker holes, no metal cutting at all besides moving the jack to the middle of my spare instead of the side wall. so a little creativity you can do it right and not use up all the space.

PM-R33 Grand Master

PM-R33

Posted
Posted
I have one of those moulded sub boxes on the way if you want to know how it fits etc. Should be here next week at the latest.

They fit really well.

I used to work for a company my mate opened up called North Coast Kustoms and as a bit of a demo display we installed two of those enclosures on either side and made a false floor with a perspex panel to view the amp underneath it.

Still had 90% of my boot space and looked extremely neat.

Kind of miss having that setup...

  • 2 weeks later...
  • 3 weeks later...
boiracer Grand Master

boiracer

Posted
Posted

always secure subs and amps ect. its funny till it fails....

a friend of mine thought he'd be cool and just wire up an amp and sub in the boot straight off a non-fused power cable from the main power behind the ignition (bodgy bodgy stuff, but in a comondoor so all i did was laugh), didnt bolt anything down at all.

First corner he threw it around it ripped the cables out of the amp and sub, shorted everything out and his steering collum proceeded to smoke and burn :)

fire was extinguished but not before all the ignition wires and important stuff was melted into a ball of stupidity

never leave electric unsecured

  • 2 weeks later...
Dumpe Community Regular

Dumpe

Posted
Posted

you can fit a pair of 10 or 12 behind the factory panels on most skylines(most cars too), in a custom fibreglass box, they don't take any room at all, looks factory still. much better then the e'blow generic box.

I have a pair of pro 12's in a carbon fibre/bullet proof lexan bandpass box's and it takes up minimal room,(tuned to match the speaker not generic boxes ) still have full access to the spare etc. ported thru the factory speaker holes, no metal cutting at all besides moving the jack to the middle of my spare instead of the side wall. so a little creativity you can do it right and not use up all the space.

any pictures

Dumpe Community Regular

Dumpe

Posted
Posted

They fit really well.

I used to work for a company my mate opened up called North Coast Kustoms and as a bit of a demo display we installed two of those enclosures on either side and made a false floor with a perspex panel to view the amp underneath it.

Still had 90% of my boot space and looked extremely neat.

Kind of miss having that setup...

any pictures

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      Input shaft bearing. They all do it. There is always rollover noise in Nissan boxes - particularly the big box. Don't worry about it unless it gets really growly.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
×
×
  • Create New...