Jump to content
SAU Community

Recommended Posts

  On 23/01/2012 at 12:01 PM, stocker said:

that what eiji class them as a td06h we talking kando's/kinugawa not trust/greddy

More or less.. Kando drops the S from all models except the L2..

Strange that he does that but no big deal. Once you understand the MHI family you read TD06H and TD06SH as the same item, no biggie. You just need to be mindful of the wheel sizes and bladecount on some of the H models as they can vary between 11 and 12 blade.

Will be interesting to measure up my turbine on my TD06-20G. My Trust compressor cover doesnt have any prefixes after the TD06. So I thought this may have meant it was a TD06S in Mitsu speak. I was trying to equate it to a Kando turbo and his plain TD06 is a bigger wheel and would not fit inside the T67 turbine housing like mine does. I believe my wheel shares the same dimensions as the L2, just has 12 blades or different pitch/back cut etc.

  On 24/01/2012 at 3:20 AM, dori34 said:

roy, does your td06 have a 2" comp housing outlet? the kando turbos come with a 2" and i'd think it's a tad small lol

unless you go a 4 in compressor cover which has a 2.5in outlet as linked below or the t67 turbo has a 2.5in outlet.............. the rest all have 2in outlet

http://www.ebay.com....=item43acaf314a

one other thing what be the a/r of the 3in compressor covers cause i see eiji has the 2.4 cover as a a/r .55 ?

Edited by stocker

Ok, so...now I just need to find a week and about 2k for dyno and spanner time. The quest to find the ideal setup on an RB20. The turbos I have to try with my 6boost manifold and Turbosmart gate are:

TD05-18G 8cm

TD06-20G 10cm

TD06L2-73HTA 8cm

TD06L2-73HTA 10cm

All to be benchlined against my TD06-20G 8cm.

The best setup will also get my baby Tomei Poncams installed and tested and then whichever setup looks the best will get a gut full of E85. It will have to go back to 98 but going to lean on it and see what I can get my track times down to with my next purchase of new tyres. Once they are past their best will throw it back to 98 for convenience. I hope the TD06L2-73HTA 8cm lives up to its promise as I want to see how a std RB20 will handle 15min track sessions with that sort of power.

I know I should not get my hopes up but am hoping I can get about 260rwkws from the TD05H-18G with E85. Would be nice if I can make +310rwkws with the 73HTA. It is meant to flow 54lb/min, which I suspect may be the start of where it may be worthwile having the baby cams with the plazmaman

I have a Trust T67-25G and TD06SH-25G laying around but they are way too much turbo for an RB20 and they are sitting around waiting for my RB24 :)

DSMGreen_01.jpg

Its basically a hack job Mistu turbo by Forced Performance. They have a 73mm billet compressor, hence the 73HTA tag. Mine runs an L2 turbine and will throw my 8cm housing on it. Meant to flow 15% more then an 20G wheel for the same response. Will see how close it comes to the claim. Be nice to have T67 power with 20G response :)

am so keen to see your results roy as within the next 12 months ill be upgrading turbo and would be awesome to see what sort of response and power the td05 18g will give....and what will happen with the poncams.....

  On 24/01/2012 at 8:38 AM, Roy said:

Its basically a hack job Mistu turbo by Forced Performance. They have a 73mm billet compressor, hence the 73HTA tag. Mine runs an L2 turbine and will throw my 8cm housing on it. Meant to flow 15% more then an 20G wheel for the same response. Will see how close it comes to the claim. Be nice to have T67 power with 20G response :)

thats a big ask but it is a nice looking wheel, how bigs the cover, I'd be keen to give it a go on my setup.. :yes:

So i find it on there site, but does it usually comes with an L2 wheel,or is that something u have done??

  On 24/01/2012 at 8:08 AM, Roy said:

Ok, so...now I just need to find a week and about 2k for dyno and spanner time. The quest to find the ideal setup on an RB20. The turbos I have to try with my 6boost manifold and Turbosmart gate are:

TD05-18G 8cm

TD06-20G 10cm

TD06L2-73HTA 8cm

TD06L2-73HTA 10cm

All to be benchlined against my TD06-20G 8cm.

Ooooh , interesting , when you do this , can you write out your full modification list sorcerer.gif

Roy how much did that 73HTA set you back? I have been considering getting one :)

The ones you see on the FP site are stock fitment with stock based housings for certain models

  On 24/01/2012 at 10:14 AM, ARTZ said:

thats a big ask but it is a nice looking wheel, how bigs the cover, I'd be keen to give it a go on my setup.. :yes:

So i find it on there site, but does it usually comes with an L2 wheel,or is that something u have done??

Its the same 3" cover as my 20G, just machined for the larger wheel. The compressor is larger in diameter, but it is lighter so will be interesting to see if there is an increase in lag. Along with dynos will do some in gear testing with the AiM and log rpm vs road speed vs boost. Should paint the full picture of what turbo makes for the faster car

  On 24/01/2012 at 11:14 AM, GTScotT said:

Roy how much did that 73HTA set you back? I have been considering getting one :)

The ones you see on the FP site are stock fitment with stock based housings for certain models

Mine is a bit of a custom jobbie getting built up locally with an EVO centre housing so has later model, more durable bearing design and water cooling and the L2 turbine. May be ok, could be a disaster. Then throwing the 73HTA compressor at it. How much? LOL...the real question is why do i have five turbos, valued at ~7k of turbos sitting around doing nothing :(

If it works you will be able to buy one off me on the following proviso..you own an RB20 :)

  On 24/01/2012 at 8:08 AM, Roy said:

Ok, so...now I just need to find a week and about 2k for dyno and spanner time. The quest to find the ideal setup on an RB20. The turbos I have to try with my 6boost manifold and Turbosmart gate are:

TD05-18G 8cm

TD06-20G 10cm

TD06L2-73HTA 8cm

TD06L2-73HTA 10cm

All to be benchlined against my TD06-20G 8cm.

The best setup will also get my baby Tomei Poncams installed and tested and then whichever setup looks the best will get a gut full of E85. It will have to go back to 98 but going to lean on it and see what I can get my track times down to with my next purchase of new tyres. Once they are past their best will throw it back to 98 for convenience. I hope the TD06L2-73HTA 8cm lives up to its promise as I want to see how a std RB20 will handle 15min track sessions with that sort of power.

I know I should not get my hopes up but am hoping I can get about 260rwkws from the TD05H-18G with E85. Would be nice if I can make +310rwkws with the 73HTA. It is meant to flow 54lb/min, which I suspect may be the start of where it may be worthwile having the baby cams with the plazmaman

I have a Trust T67-25G and TD06SH-25G laying around but they are way too much turbo for an RB20 and they are sitting around waiting for my RB24 :)

DSMGreen_01.jpg

Hey Roy, what size housings you got on the TD06SH-25g? if you wanna get rid of it let me know.

  On 24/01/2012 at 11:41 AM, urtwhistle said:

Hey Roy, what size housings you got on the TD06SH-25g? if you wanna get rid of it let me know.

It's a 10cm housing. Not sure I want to sell it any more. I cant really sell it as who is going to pay over 2k for it when you can get a Kando for ~$800 :(

med_gallery_462_50_107117.jpg

med_gallery_462_50_205958.jpg

med_gallery_462_50_231537.jpg

med_gallery_462_50_100815.jpg

med_gallery_462_50_77937.jpg

med_gallery_462_50_155372.jpg

Actually looking at these pics now the compressor cover tag says TD06H. I thought it said SH? Anyway, its the same turbo from the earlier page side by side with the L2-20G

wow 2k, I never realized thats what the Trust branded 1's were worth. I was thinking of offering you what a KD was worth lol.

When you look at the turbo on a side profile, I'm amazed that the tiny little turbine housing flows what they do. Since you have played with these turbo's so much whats your opinion for a 3L & TD06H-25G with 3",3" port shrouded & 4" inlets. what housing would you choose? Would there be any advantage that you can think of by using the TD07S housing version's of the same turbo?

cheers for your help.

Yeh, its only done dyno time so like new. But nobody is going to pay $2200 for it when you get get a "Kando the Great" for $800.

If I had an RB30 i dont think i would run any of these turbs. I think you would get a better result out of the GTX3076, more responive and the billet compressors seem to give you a bit more legs at higher pressure ratios. So probably bag you a more responsive 350rwkws.

  On 24/01/2012 at 8:08 AM, Roy said:

TD05-18G 8cm

TD06-20G 10cm

TD06L2-73HTA 8cm

TD06L2-73HTA 10cm

All to be benchlined against my TD06-20G 8cm.

The best setup will also get my baby Tomei Poncams installed and tested and then whichever setup looks the best will get a gut full of E85. It will have to go back to 98 but going to lean on it and see what I can get my track times down to with my next purchase of new tyres. Once they are past their best will throw it back to 98 for convenience. I hope the TD06L2-73HTA 8cm lives up to its promise as I want to see how a std RB20 will handle 15min track sessions with that sort of power.

I know I should not get my hopes up but am hoping I can get about 260rwkws from the TD05H-18G with E85. Would be nice if I can make +310rwkws with the 73HTA. It is meant to flow 54lb/min, which I suspect may be the start of where it may be worthwile having the baby cams with the plazmaman

Awesome test, looking forward to hearing the results! I'd love to have seen a 68HTA in the 8cm TD06 housing too...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 馃
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
  • Create New...