Jump to content
SAU Community

Recommended Posts

3540 shaft snapped in half and the Kando cost less than just a core for the garrett.

essencially the same engine apart from new injectors, rochester 1000's and a the T67, it is spooling up heaps earlier than the 3540, around 1000-1500 rpm earlier which makes me think its the housing.

thats quite early but i think the 8cm would be even earlier.

take a few photos of the rear housing, i am fairly confident i can tell the difference. Take pics from around the flange area.

im fairly certain that a 10cm housing has more of a taper on the exit side of the T3 flange than it does on the CHRA side, whereas an 8cm has the same amount of taper from the flange on both sides and the snail shell is a little thinner.

This is my observation but im not honestly sure this is correct!

The genuine garrett .82 will be better suited. The .73 (10cm) kando housing is a tiny thing.

There are also better options available for that sort of power when talking 'responsive' and 400kw on a dirty thirty. Bare in mind a 35R is similar in size to a precision 6262.

A bush bearing PT can be had for roughly 1k delivered, and would be a hands down winner if you went for the T4 TS option. Single gate to keep costs low will still work a treat.

Finally here is a couple of pics of my turbo housing, i think it is a 10cm but it is just too small for my 25/26 with cams. We ended up getting 275RWKW out of it at 20psi on BP ultimate. It spools up to full song at 3500 and starts to drop off around 6000. It is very good to drive but we were pretty disappointed at the power output.

post-2388-0-18249500-1353379281_thumb.jpg

post-2388-0-39146500-1353379290_thumb.jpg

Simon, i suggest waiting to see how i go before getting the T67.

Finally here is a couple of pics of my turbo housing, i think it is a 10cm but it is just too small for my 25/26 with cams. We ended up getting 275RWKW out of it at 20psi on BP ultimate. It spools up to full song at 3500 and starts to drop off around 6000. It is very good to drive but we were pretty disappointed at the power output.

post-2388-0-18249500-1353379281_thumb.jpg

post-2388-0-39146500-1353379290_thumb.jpg

Simon, i suggest waiting to see how i go before getting the T67.

Worst pictures ever haha But I think it's a 10cm by the looks

In that case I can almost guarantee you something is wrong with your set up and not the turbo... These things don't drop off at high revs, we went well past 8000rpm with mine and power was still going north.

You are about 50rwkw down on where you should be... Got a graph?

Looking for a Kando for my 26/30. Has anyone got any thoughts on this? Basically a 3582r with .73 rear housing. Want to make a responsive 400 rwkw http://item.mobileweb.ebay.com.au/viewitem?itemId=120892863434

Hey Simon, I got a Kando TD06H-25g with the biggest houseing they make on my neo 25/30. It's not tuned above 5000rpm cos I need to replace my wastegate ( I'm not doing it untill my new 4wd arrives). To compare I had a Hypergear Gt3576 that made about 370rwhp on Ultimate 98 on Hyperdrive's dyno (In WA). With my rev limit set at 4500rpm I think I could safely say that the new kando turbo is massivly more powerful and massively more responsive.

I have herd of people running T67's on 3L's but I honestly reckon that it would be happier with the slightly bigger TD06H-25G.

But that all being said my car isn't fully tuned so I ahve no idea when it will stop making power.

The genuine garrett .82 will be better suited. The .73 (10cm) kando housing is a tiny thing.

There are also better options available for that sort of power when talking 'responsive' and 400kw on a dirty thirty. Bare in mind a 35R is similar in size to a precision 6262.

A bush bearing PT can be had for roughly 1k delivered, and would be a hands down winner if you went for the T4 TS option. Single gate to keep costs low will still work a treat.

i know nothing about the PT turbos.. just did some reading up on them.. looks to be the goods! might go with a 6262 i reckon

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nah, new members can't post pics until they reach a certain post count. If I get a chance I'll promote you to full member, if @Prank or someone else doesn't get there first.
    • Drilled the rubber out on a slow speed and it didn't catch much at all. Probably only half a dozen holes was enough to shred the rubber and it dropped off easily leaving the inner sleeve behind. Will tackle that later
    • I havent bought a manual cover for the dash yet and no cluster change, won't bother me too much, I just need to get that auto box gone, manual in! I miss my manual. 🤪. We started last weekend and managed to get the box out. Planning to start putting it in this weekend and then order a single piece tail. We were super careful to take time and not damage anything. It's my first time working under the car.  With my S15 mainly worked in the bay. This time, it was a headache because of three or four bolts only. They simply didnt want to leave thei homr and the one securing the tailshaft, another above the GB, and the one securing the lipstick was a shit. Mates mate, Davo caught fire 🤣, nearly opened his chest up with a grinder 🤦🏽‍♂️ and both mates nearly had a plate from the box land and slit their head open. Fun times. We all survived. Not the easiest working with limited access on jackstands. As I'm sure we can agree these are the memories which make us love our car. For all three of us, was an awesome weekend and Sunday 3.30am before tools down was a fantastic effort. I need to upload pics, but looks like it needs to be via Url now. We used to be able to just upload pics back in the day. It's been that long! 🤪 Im currently spraying rustoleum under body, not because it's rusted. It's super clean, but just so it's protected for the next 10 years. There was a few surface rust spots. Which pretty much wiped off with a 3M scourer.  Really impressed with how well the previous owner maintained it. Bank account went down so quick! Service, then GB - managed to get a spanking new 34 genuine box from Nissan. All the rest of the conversion parts from Kudos.  Went with a Nismo short shifter. New pedals and Exedy Clutch and FW. Ordered the Prp Rear Main Retainer kit which should arrive Friday and my first engine mod part just like I did with my S15 will be the Tomei Expreme Turbo Outlet. Already on order. It'll likely sleep next to me on a pillow during the coming months. 🥰 Last build was on my JET200GT profile and on SAU and Hardtuned I had documented the build. Planning to try to do that again. Brands feel scarce now. Wish we still had ARC and Apexi parts readily available. Exhaust - need some advice on this. I had an Apexi exhaust on the S15 and loved the tone. My mate had a HKS HP Silent on his 33 and suggested I go with that to avoid drone. I can't remember hearing an RB25DET running that so will likely need to wait for a meet or something to hear it.  Not after big power, just enjoy building it, and drivability with minimal negative attention.
    • Have a chat with Ben at Moore Performance or Jesse at JS Performance.
    • Thanks both. All good advice. Reminds me of drilling through stone wall for drainage pipe 😬 I'll let you know how I get on if I still have use of my hands afterwards 😅
×
×
  • Create New...