Jump to content
SAU Community

Recommended Posts

Hey Ppls,

Previously I thought the extra throttle body type device was a traction control thing which shut when wheelspin was evident.

I have since been told that this is actually a Variable Intake Flow thingo which acts to increase airflow speed at low rpm by closing like a normal throttle body, and then opening up at high rpm to give bulk airflow.

Now, PowerFCs are suppose to control all features of the engine management, and I would assume that this is a very important part of the Neo 6 engine.

To those who know, does the R-34 PowerFC allow you to control the activity of this throttle body device........??

I would assume that you could adjust this similar to the way you can with the NVCS.

Having said that though, it might have a link to TPS in order to give the best results depending on a lot of other variables......

Anybody with any experience??

Cheers

BASS OUT

Link to comment
https://www.sau.com.au/forums/topic/34851-r34-neo-straight-6-power-fc-question/
Share on other sites

Are you talking about the bit that sits across the inside of the plenum? it's open at low revs, then closes at high revs...speeds up the flow of air at high RPM. If you disconnect it you'll notice the car runs like a dog from about 3200-5000ish,then picks up in the last bit of the range.

Yep, that's the bit.

Any definent answers??

when I disconnected the plug to it last night, the Engine Warning light came and on the Slip/TCS off light lit up and I took it for a drive.

I didn't really notice a lot of difference but the car was cold and I couldn't really give it a good thrashing.

Guest RedLineGTR

The thing that is in front of the throttle body, is for the Traction Control System :D its what limits your revs when u are wheels spinning from the line, hence if you try to launch with the TCS on then you bog down quite bad. Hope it answers you question.

Guest RedLineGTR

The Power Fc will control everything the same as in other skylines (in one way or another) the Neo engine is tuned for more power (more R&D) over the past models. The TCS Has a Seperate ECU for what it does and u cant change any items of how it behaves with the power fc nor do i know any companys that have Tuned it in one way or another.

Guest RedLineGTR

I hope this is what u mean by your question. When the TCS is activated it is activated and if the car starts to slip highly then it kicks in just like i throttle body, like if you are on the pedal to the floor the TCS can ajust its throttle and limit your revs. If the system is off then the air flows how its meant to without any interuption.

My experience with the traction control is as follows.

Going around slight corners and nailing it, the car will pull lose power and then accelerate once grip is gained again.

But in the wet the car will drop spark and the engine will 'strobe' (for want of a better word) for a second and then accelerate, at which point traction will be lost again, and then it will strobe again.

I think maybe in moderate losses of traction, the blade might close, butin big ones it drops sparky and really pulles the reigns in.

If it only works for traction control, I wonder it there is any merit in using it as a variable intake diameter type device????

What makes you think it "drops sparky"? It just closes the valve completely starving the engine of air and probably cuts the fuel at the same time. If you cut spark it would backfire when you gave it back.

At it's most basic it just cuts power so you can get traction back and if you keep your foot down then it will spin the wheels again, thus restarting the whole process.

Abo Bob.

The sound it makes it identical to the sound that my car makes when misfiring on plugs that haven't been gapped properly.

That's why i made the assumption.

But I have been wrong before!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • To expand on this to help understanding... The bigger/longer the block is, the more it's going to work to sit on your far away high areas, and not touch the low stuff in the middle. When you throw the guide coat, and give it a quick go with a big block, guide coat will disappear in the high spots. If those high spots are in the correct position where the panel should be, stop sanding, and fill the low spots. However, using a small block, you "fall off" one of the high spots, and now your sanding the "side of the hill". Your little block would have been great for the stone chips, where you only use a very small amount of filler, so you're sanding and area let's say the size of a 5/10cent piece, with something that is 75*150. For the big panel, go bigger!   And now I'll go back to my "body work sucks, it takes too much patience, and I don't have it" PS, I thought your picture with coloured circles was an ultra sound... That's after my brain thought you were trying to make a dick and balls drawing...
    • Oh I probably didn't speak enough about the small sanding block for blocking large areas.  In the video about 3 minutes in, he talks about creating valleys in the panel. This is the issue with using a small sanding block for a large area, it's way too easy to create the valleys he is talking about. With a large block its much easier to create a nice flat surface.  Hard to explain but in practice you'll notice the difference straight away using the large block. 
    • Yep I guessed as much. You'll find life much easier with a large block something like this -  https://wholesalepaint.com.au/products/dura-block-long-hook-loop-sanding-block-100-eva-rubber-af4437 This is a good demo video of something like this in use -    You have turned your small rock chip holes into large low spots. You'll need to fill and block these low spots.  It's always a little hard not seeing it in person, but yes I would go ahead and lay filler over the whole area. Have a good look at the video I linked, it's a very good example of all the things you're doing. They went to bare metal, they are using guide coat, they are doing a skim coat with the filler and blocking it back. If what you're doing doesn't look like what they are doing, that's a big hint for you  
    • The odometer does go up when driving.  Does this tell it is an issue with the speedometer itself?    Where can I look for replacement cluster? Or speedo? I can likely do the repair.. Will ER34 cluster work on HR34? Or do I need a HR34 20GT S2 specifically lol   
×
×
  • Create New...