Jump to content
SAU Community

Recommended Posts

Hello mates,

I am planning on buying a CF vented hood to reduce some weight but not sure about it. Is it save to drive in the rain with an opening like that? It looks like the water will just poor down on the belts and alternator. My car is daily driven and i dont have a garage to park it in.

I did a search but couldnt find anything, if anyone can point me in the right direction.

Thanks.

  • Nope 1
Link to comment
https://www.sau.com.au/forums/topic/348707-vented-hood-in-the-rain/
Share on other sites

water also comes up from underneith... and no problems there?

Is that weight saving really going to make your 'street' car any faster... 60km/h is still 60km/h.

You'd be better spending that money of a gym membership and losing weight that way (not saying your a chubsy whubsy... just that people can weigh between 70 to 120kg's)

  • Nope 2

As long as the vents were not directly above the exhaust manifold and intake filters that it shouldn't be too much issue,

There are quite a few manufacturers that include bonnet vents from factory and some of these like the Toyota Celica vent their directly above the turbo and alternator without affecting the vehicles reliability.

if the Bearings on your alternator, power steering, and air-conditioning were subjected to lot of water you may find they would wear quicker but I doubt it's going to be that obvious.

Also watch out for water that gets into the valley where the coils are as the plugs will rust and the moisture will work its way into the boots and cause a missfire, it happened to me.

Thanks everyone for the honest replies, i was just a bit concern and didnt want to ruin my engine which i rebuilt. My plan to reduce weight for this "street" car is for when i'm ready with my new setup i can head up to the drag strips and have some fun there.

And to Mr Barraspalding, thanks for caring about my weight, but i already have a gym membership pass and i go there 4 times a week. Next time if you care so much why not ask first instead of being an ass...

water also comes up from underneith... and no problems there?

Is that weight saving really going to make your 'street' car any faster... 60km/h is still 60km/h.

You'd be better spending that money of a gym membership and losing weight that way (not saying your a chubsy whubsy... just that people can weigh between 70 to 120kg's)

  • Nope 1

I've had 3 different types of vented bonnets the 1st was good had the one vent which was centered over the top of the gap between the radiator and front of the engine. I never had any issues with water with this one.

DSCN0177.jpg">

I then changed to a CF Z-Tune style one and the quality was a bit average and had it fitted to the car for a day or two in the panel shop. After the car was outside and in the rain for a little there was water in the engine bay even with the 'tray' fitted (when i opened the bonnet the water collected in the tray spilt in the engine bay anyways)

I then got the Nismo carbon R Tune one which has the rain channels and no water gets into the bay at all as long as you dont point the hose directly in there. The quality of this is unreal..

IMG_2649.jpg"

This is only my expirence with them and im sure there are others who have never had any dramas with any vented bonnet. But living up here in Mackay the rain can be quite tropical at times coming in thick and fast lol..:D

Cheers

Kingy

  • Like 1

same experience as king.

if you can find one with the venting forward of the valley cover (coil and spark cover) you will be fine.

but if the venting is behind the cover you will get water in there when its raining and the car is stationary, while its moving you

will be fine.

The water falls between the engine and the radiator on this one.

g-force0011.jpg

water falls on front of the cover on this one while the car is stationary.

18072010135_clear.jpg

Edit...both of those are 3rd of the weight of the oem bonnet.

I've had 3 different types of vented bonnets the 1st was good had the one vent which was centered over the top of the gap between the radiator and front of the engine. I never had any issues with water with this one.

DSCN0177.jpg">

I then changed to a CF Z-Tune style one and the quality was a bit average and had it fitted to the car for a day or two in the panel shop. After the car was outside and in the rain for a little there was water in the engine bay even with the 'tray' fitted (when i opened the bonnet the water collected in the tray spilt in the engine bay anyways)

I then got the Nismo carbon R Tune one which has the rain channels and no water gets into the bay at all as long as you dont point the hose directly in there. The quality of this is unreal..

IMG_2649.jpg"

This is only my expirence with them and im sure there are others who have never had any dramas with any vented bonnet. But living up here in Mackay the rain can be quite tropical at times coming in thick and fast lol..:D

Cheers

Kingy

If don't mind me asking, where did you get the z tune style from and how much did the r tune set you back? :D

Thanks!!

they dont make a 33 GT-R one at Nismo

i run the genuine R Tune Nismo Omori bonnet on the 34. It does as stated have rain channels under the bonnet and is Dry Carbon

The best one for the 33 is the design by Top Secret imo, it works alot better, than the copies of the z tune for the "33"

  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You are selling this? I have never bought something from marketplace...i dont know if i trust that enough. And the price is little bit "too" good...
    • https://www.facebook.com/share/19kSVAc4tc/?mibextid=wwXIfr
    • It would be well worth deciding where you want to go and what you care about. Reliability of everything in a 34 drops MASSIVELY above the 300kw mark. Keeping everything going great at beyond that value will cost ten times the $. Clutches become shit, gearboxes (and engines/bottom ends) become consumable, traction becomes crap. The good news is looking legalish/actually being legal is slighly under the 300kw mark. I would make the assumption you want to ditch the stock plenum too and want to go a front facing unit of some description due to the cross flow. Do the bends on a return flow hurt? Not really. A couple of bends do make a difference but not nearly as much in a forced induction situation. Add 1psi of boost to overcome it. Nobody has ever gone and done a track session monitoring IAT then done a different session on a different intercooler and monitored IAT to see the difference here. All of the benefits here are likely in the "My engine is a forged consumable that I drive once a year because it needs a rebuild every year which takes 9 months of the year to complete" territory. It would be well worth deciding where you want to go and what you care about with this car.
    • By "reverse flow", do you mean "return flow"? Being the IC having a return pipe back behind the bumper reo, or similar? If so... I am currently making ~250 rwkW on a Neo at ~17-18 psi. With a return flow. There's nothing to indicate that it is costing me a lot of power at this level, and I would be surprised if I could not push it harder. True, I have not measured pressure drop across it or IAT changes, but the car does not seem upset about it in any way. I won't be bothering to look into it unless it starts giving trouble or doesn't respond to boost increases when I next put it on the dyno. FWIW, it was tuned with the boost controller off, so achieving ~15-16 psi on the wastegate spring alone, and it is noticeably quicker with the boost controller on and yielding a couple of extra pounds. Hence why I think it is doing OK. So, no, I would not arbitrarily say that return flows are restrictive. Yes, they are certainly restrictive if you're aiming for higher power levels. But I also think that the happy place for a street car is <300 rwkW anyway, so I'm not going to be aiming for power levels that would require me to change the inlet pipework. My car looks very stock, even though everything is different. The turbo and inlet pipes all look stock and run in the stock locations, The airbox looks stock (apart from the inlet being opened up). The turbo looks stock, because it's in the stock location, is the stock housings and can't really be seen anyway. It makes enough power to be good to drive, but won't raise eyebrows if I ever f**k up enough for the cops to lift the bonnet.
    • There is a guy who said he can weld me piping without having to cut chassis, maybe I do that ? Or do I just go reverse flow but isn’t reverse flow very limited once again? 
×
×
  • Create New...