Jump to content
SAU Community

Recommended Posts

Hello mates,

I am planning on buying a CF vented hood to reduce some weight but not sure about it. Is it save to drive in the rain with an opening like that? It looks like the water will just poor down on the belts and alternator. My car is daily driven and i dont have a garage to park it in.

I did a search but couldnt find anything, if anyone can point me in the right direction.

Thanks.

  • Nope 1
Link to comment
https://www.sau.com.au/forums/topic/348707-vented-hood-in-the-rain/
Share on other sites

water also comes up from underneith... and no problems there?

Is that weight saving really going to make your 'street' car any faster... 60km/h is still 60km/h.

You'd be better spending that money of a gym membership and losing weight that way (not saying your a chubsy whubsy... just that people can weigh between 70 to 120kg's)

  • Nope 2

As long as the vents were not directly above the exhaust manifold and intake filters that it shouldn't be too much issue,

There are quite a few manufacturers that include bonnet vents from factory and some of these like the Toyota Celica vent their directly above the turbo and alternator without affecting the vehicles reliability.

if the Bearings on your alternator, power steering, and air-conditioning were subjected to lot of water you may find they would wear quicker but I doubt it's going to be that obvious.

Also watch out for water that gets into the valley where the coils are as the plugs will rust and the moisture will work its way into the boots and cause a missfire, it happened to me.

Thanks everyone for the honest replies, i was just a bit concern and didnt want to ruin my engine which i rebuilt. My plan to reduce weight for this "street" car is for when i'm ready with my new setup i can head up to the drag strips and have some fun there.

And to Mr Barraspalding, thanks for caring about my weight, but i already have a gym membership pass and i go there 4 times a week. Next time if you care so much why not ask first instead of being an ass...

water also comes up from underneith... and no problems there?

Is that weight saving really going to make your 'street' car any faster... 60km/h is still 60km/h.

You'd be better spending that money of a gym membership and losing weight that way (not saying your a chubsy whubsy... just that people can weigh between 70 to 120kg's)

  • Nope 1

I've had 3 different types of vented bonnets the 1st was good had the one vent which was centered over the top of the gap between the radiator and front of the engine. I never had any issues with water with this one.

DSCN0177.jpg">

I then changed to a CF Z-Tune style one and the quality was a bit average and had it fitted to the car for a day or two in the panel shop. After the car was outside and in the rain for a little there was water in the engine bay even with the 'tray' fitted (when i opened the bonnet the water collected in the tray spilt in the engine bay anyways)

I then got the Nismo carbon R Tune one which has the rain channels and no water gets into the bay at all as long as you dont point the hose directly in there. The quality of this is unreal..

IMG_2649.jpg"

This is only my expirence with them and im sure there are others who have never had any dramas with any vented bonnet. But living up here in Mackay the rain can be quite tropical at times coming in thick and fast lol..:D

Cheers

Kingy

  • Like 1

same experience as king.

if you can find one with the venting forward of the valley cover (coil and spark cover) you will be fine.

but if the venting is behind the cover you will get water in there when its raining and the car is stationary, while its moving you

will be fine.

The water falls between the engine and the radiator on this one.

g-force0011.jpg

water falls on front of the cover on this one while the car is stationary.

18072010135_clear.jpg

Edit...both of those are 3rd of the weight of the oem bonnet.

I've had 3 different types of vented bonnets the 1st was good had the one vent which was centered over the top of the gap between the radiator and front of the engine. I never had any issues with water with this one.

DSCN0177.jpg">

I then changed to a CF Z-Tune style one and the quality was a bit average and had it fitted to the car for a day or two in the panel shop. After the car was outside and in the rain for a little there was water in the engine bay even with the 'tray' fitted (when i opened the bonnet the water collected in the tray spilt in the engine bay anyways)

I then got the Nismo carbon R Tune one which has the rain channels and no water gets into the bay at all as long as you dont point the hose directly in there. The quality of this is unreal..

IMG_2649.jpg"

This is only my expirence with them and im sure there are others who have never had any dramas with any vented bonnet. But living up here in Mackay the rain can be quite tropical at times coming in thick and fast lol..:D

Cheers

Kingy

If don't mind me asking, where did you get the z tune style from and how much did the r tune set you back? :D

Thanks!!

they dont make a 33 GT-R one at Nismo

i run the genuine R Tune Nismo Omori bonnet on the 34. It does as stated have rain channels under the bonnet and is Dry Carbon

The best one for the 33 is the design by Top Secret imo, it works alot better, than the copies of the z tune for the "33"

  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Johnny is sad now... Because you didn't get Bosch Motorsport ABS.  
    • Hey keep the ideas coming, I'm always keen on projects! But, problem fixed!  I got a cheapie ozito scope from Bunnings and had a good look in and around the bearing and sensor hole. I couldn't see a smoking gun but the bearing looked a bit strange, especially when comparing with a new one. I thought the cover had come off the bearing magnets.  Sorry for pics of a screen, I didn't have an SD card.     Good thing I had the old one to inspect. So, given I'm like a pit crew with wheel bearings and luckily I had a spare bearing because I f**ked up my parts order, I decided to just smash it out. Got the old one out in about an hour. So much easier when the parts haven't had a chance to rust together yet. 😂 And, well, found the problem.    In the second pic at about the 8 o'clock position, you'll see what I think is the tip of the old sensor.  The new sensor has definitely been rubbing but it's all intact, just a little shiny so I'm hoping it's fine.  The car brakes perfectly now and no errors.  I think the job took about 2.5h in the end. 👍🏻 I really appreciate the help in here as usual. Thanks guys.
    • I was only looking because I saw some drops on the ground but it wasn't alot. Recently had it serviced will ask the mech to confirm. Find it strange that it looks standard though, can see in another photo of a random box 
    • So...not sure if you know if that has always been there or why you went looking. It could be old damage from a clutch explosion, or even just the gearbox got dropped somewhere along the line. Basically, you should seal it up to stop oil and dust getting into the bellhousing, but it doesn't matter too much and is not structural. I'd suggest something like a glob of JB Weld. BTW what gearbox oil are you running, I would guess the breather has been spewing it everywhere.
    • Hey Duncan thanks for your reply. Sorry mate I know the photos are shit.  Took another photo for reference. Seems the casing does have a hole in it looking on the net, fluid seeping out. Added a photo   
×
×
  • Create New...