Jump to content
SAU Community

Got A Gtr 34 Vspec Ii


Recommended Posts

Hi Guys,

If I'm posting in the incorrect area or if theres already a thread please link me. Being a Stagea owner i dont know where to look n search didnt help me.

My Girlfriends brother has just purchased a GTR34 Genuine VSpec II with about 50?00kms on the clock. previously owned by some rich business owner in Aus aswell..

He picked up the car yesterday.

I drove it, feels like a brand new car, no miss no lump no odd spots. Perfect. very good buy.

I want to know what type of things need to be done when you purchase one, ie maintanence.

General Service was (apparently) done 2 weeks ago.

What type of oils are recomended for;

-engine

-diff

-trans

-hicas

-atteza

is there anything else he should be worrying about?

Your help is much appreciated. I'm forcing him to get on the forum tonight so he can have an input as well.

Thanks People!

Link to comment
Share on other sites

^ ^ ^ as above... plus...

Has the 40,000km service been done in full?

Official NISSAN Owner's Manual says...

* Engine oil replaced every 5000km or 6 months whichever comes first

* Oil Filter replace every 10,000km interval

* Drive Belts inspect at 40,000 80,000 100,000km

* Engine antifreeze (ethylene glycol based) replace at 40,000 80,000 100,000km

* Cooling System inspect every 20,000km interval

* Air Cleaner Filter (viscous paper type) replace at 40,000 80,000 100,000km

* Intake and Exhaust Valve Clearance inspect if valve noise increases

* Fuel Lines inspect every 40,000 interval

* Fuel Filter replace every 40,000 interval (but every 20,000km with frequent track use)

* Spark Plugs (platiunum-tipped) replace at 100,000km intervals

* Heated Oxygen Sensor (exhaust gas sensor) inspect at 40,000 80,000 100,000km

* EVAP Vapour Lines inspect at 40,000 80,000 100,000km

* Timing Belt replace at 100,000km intervals

* Brake and Clutch Fluids inspect every 10,000km interval

* Brake Fluid replace at 40,000 80,000 100,000km

* Brake Booster Vacuum Hoses, Connections & Check Valve inspect at 40,000 80,000 100,000km

* Power Steering Fluid and Lines inspect for levels and leaks every 10,000km interval

* Brake, Clutch and Exhaust Systems inspect every 10,000km interval

* Manual Transmission Gear Oil inspect for levels and leaks every 10,000km

* Differential Gear Oil inspect every 10,000km (every 5,000km if used on track)

* Transfer Fluid replace at 40,000 80,000 100,000km and inspect at 10,000km intervals

* Steering Gear & Linkage, Axle & Suspension Parts, Propeller Shafts & Drive Shafts inspect at 20,000km intervals (every 10,000km if on track)

* Wheel Alignment, Wheel Balance, Wheel Rotation inspect at 20,000km intervals

* Brake Pads, Rotors, Lines inspect at 10,000km intervals (every 5,000km if on track)

* Locks, Hinges, Bonnet Latch lubricate at 10,000km intervals

* Seat Belts, Buckles, Retractors, Anchors & Adjuster inspect at 20,000km intervals

* Foot Brake, Parking Brake & Clutch (for free play, stroke & operation) inspect at 10,000km intervals

* Ventilation Air Filter replace at 20,000km intervals

* Air Bag Systems inspect after 10 years and then at 2 year intervals

Link to comment
Share on other sites

^ ^ ^ as above... plus...

Has the 40,000km service been done in full?

Official NISSAN Owner's Manual says...

* Engine oil replaced every 5000km or 6 months whichever comes first

* Oil Filter replace every 10,000km interval

* Drive Belts inspect at 40,000 80,000 100,000km

* Engine antifreeze (ethylene glycol based) replace at 40,000 80,000 100,000km

* Cooling System inspect every 20,000km interval

* Air Cleaner Filter (viscous paper type) replace at 40,000 80,000 100,000km

* Intake and Exhaust Valve Clearance inspect if valve noise increases

* Fuel Lines inspect every 40,000 interval

* Fuel Filter replace every 40,000 interval (but every 20,000km with frequent track use)

* Spark Plugs (platiunum-tipped) replace at 100,000km intervals

* Heated Oxygen Sensor (exhaust gas sensor) inspect at 40,000 80,000 100,000km

* EVAP Vapour Lines inspect at 40,000 80,000 100,000km

* Timing Belt replace at 100,000km intervals

* Brake and Clutch Fluids inspect every 10,000km interval

* Brake Fluid replace at 40,000 80,000 100,000km

* Brake Booster Vacuum Hoses, Connections & Check Valve inspect at 40,000 80,000 100,000km

* Power Steering Fluid and Lines inspect for levels and leaks every 10,000km interval

* Brake, Clutch and Exhaust Systems inspect every 10,000km interval

* Manual Transmission Gear Oil inspect for levels and leaks every 10,000km

* Differential Gear Oil inspect every 10,000km (every 5,000km if used on track)

* Transfer Fluid replace at 40,000 80,000 100,000km and inspect at 10,000km intervals

* Steering Gear & Linkage, Axle & Suspension Parts, Propeller Shafts & Drive Shafts inspect at 20,000km intervals (every 10,000km if on track)

* Wheel Alignment, Wheel Balance, Wheel Rotation inspect at 20,000km intervals

* Brake Pads, Rotors, Lines inspect at 10,000km intervals (every 5,000km if on track)

* Locks, Hinges, Bonnet Latch lubricate at 10,000km intervals

* Seat Belts, Buckles, Retractors, Anchors & Adjuster inspect at 20,000km intervals

* Foot Brake, Parking Brake & Clutch (for free play, stroke & operation) inspect at 10,000km intervals

* Ventilation Air Filter replace at 20,000km intervals

* Air Bag Systems inspect after 10 years and then at 2 year intervals

Thanks a million mate!

Well I can guarntee the oil was changed as theres a new ryco filter on it. not sure whats in there though. Hoping 300v, the way he'll thrash it.

belts are definitely done as theres absolutely no wear n tear on it.brake fluid powersteering looks clean to me. Sparkies i wouldnt know, I'de have to get into it to check.

no leaks in the trans or hicas or atteza. but one think i noticed for the HICAS bottle in the boot is that the fluid is two different colours. ie maybe nulon/matic j would this be a problem as the nulon was a direct replacement? the HICAS light did come on yesterday but after turning it off and back on it dissapered.

Had a look and theres quite abit of meat for the Brembo's.. the disc's look like theyve been machines or still new(theres no lips) [these brembo's are bitey as!]

to check some of the other stuff i want to get under the car like the O2 sensor etc..

Need to check the air filter, fiddly box though. recomend oiled or not? I know oiled can F with the AFM which might cause limp.

a question with the standard boost though. I always thought they would run an 10-11psi at max. this one has the Boost controller diconnected as back to stock, and is running 1.1bar max. and thats warmish weather aswell. I've heard stock turbo's should NEVER be pushed more than 1.2bar. The ECU has been changed, not sure of the brand I havent checked. but according to the seller its doing 330kw at the fly.

for cooling options what should i be looking at ie trans oil, engine oil, or is the stock stuff good? im trying to get him to do it all soon as he wont be driving it until he's off his P's(Dont ask)

thanks people.

Link to comment
Share on other sites

lol yeh hes not driving it much, only locally in his area to get the feel of it. hope he doesnt get pulled over though..

I took this pic today of our cars..its the only pic i have.. hes done well for a well maintained car

post-77654-0-09532800-1293962699_thumb.jpg

Link to comment
Share on other sites

What paint code is it Aaron?

The Vspec 2's still have the ceramic turbos yeah? I think stock boost would be around the 10psi mark.

As for power standard - they were sold under the 206kw gentlemans agreement but at the engine could be around the 230kw mark. Unleash the boost and the story changes very quickly :)

Link to comment
Share on other sites

Paint Code?

Well from my own knowledge I think it was only the NUR Gtr's that were a steel wheel BB turbo. So i do believe this *should* be ceramic backed. with a Disconnected Boost controller, the boost was hitting a peak pressure of 1.1bar (15~ psi) Are the in car gages acurate? I'm told they are

ok well i think my questions now changed,

with just and ECU "PowerFC" thats installed, what type of power can be rached based on stock everything?

Thanks heaps mate

Link to comment
Share on other sites

Paint Code?

Yeah sorry I am trying to pick paint at the moment - the R34's came in a few different silvers (see here). Kinda looks like sparkling silver to me - it would have the paint code in the engine bay on the plate with the vin / engine no etc.

ok well i think my questions now changed,

with just and ECU "PowerFC" thats installed, what type of power can be rached based on stock everything?

I personally wouldn't push the ceramic turbos over 12psi but thats me. Many have ran them at around 14psi reliably but then again others have not - and when they shatter they can take the engine with them. I would prefer to spend $3k up front on some steel wheel turbos for insurance, rather than $15k on an engine + turbos after disaster.

I am not sure how the R34's are tuned from factory, but the difference going to power FC on my R32 was unbelievable. It netted probably an extra 20rwkw just from trimming the fuel. The stock R32 ECU had the AFR's at around 10:1 - very rich. After the change fuel consumption around town also dropped dramatically - like from 250km per tank to 350-450km.

At a guess stock standard + well tuned power fc, and boost at 12psi I would think peak around 200rwkw. Add some steel turbos @ 16/17psi, maybe a nismo fuel pump for insurance and a decent exhaust and you will start getting up to the 300rwkw mark.

Link to comment
Share on other sites

ok well like i said, for some reason its reading 1.1bar. without a EBC/BC

the only thing i can think of is if the previous owner had replaced em with Nismo turbos off the NUR. they look stock. but the actuators run at 14psi

im gonna plug my informeter into it, and see what comes out of that. Atleast im certain its figures will be 100% spot on. pain in the ass though.

I'll find out the paint code when im fiddling with it tonight n let you know. I'm also wondering if I should get the VIN fasted to find out its authenticiy of being a vspec ii

Link to comment
Share on other sites

Yeah its quite easy to up them to 14-15psi. From factory there is a brass restrictor inside one of the hoses to the standard boost control solenoid. It is designated by a yellow or white stripe on the hose. Removing this will allow boost to get up above 14psi - the last owner may have done this.

Standard R34 ceramic's should have a compressor cover with 0.53 a/r stamped on it. N1's will be 0.6 or 0.42.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Meh, whilst the Honda is a "really" good car and has potential if you want to drop coin on, it was uninspiring for me to look at, but, it did serve its purpose and is now in the boys hands, his happy, his girl is happy, as she wasn't to keen on the noisy old Patrol, and most importantly, the Minister for War and Finances is extremely happy that her "little baby boy" (6'2 nugget who is currently training to be a copper, which will make 3 coppers in the immediate "circle of trust") has a well sorted reliable car that doesn't guzzle diesel Me, I'm more than happy with the NC MX5 that I replaced it with, it's a fun little car that I like looking at, like driving, and yes..... I do like the fact that the maintenance and modifications that I have done/will do are plentiful and relatively cheap, well........ while staying naturally aspirated slow that is, and that's all I really need for a fun little daily, I can rev the 5hit out of it rowing through the gears and never really break the speed limit  In saying that wicked word, "modifications", I've already ordered something for some noise and an additional "3 ish" horse powers, or whatever it gives, in the form of a header, and, a new set of "cheapo" BC coilovers that are already sitting in the shed waiting to get put in, I had the same BC's in my old NB and found they were fine for the street, hwy, and the occasional track days I did in it, they have 6kg front and 4kg rear springs which is about 10% stiffer than the stock springs which I found worked well for their price  I've also already been in touch with MX5 Mania in Dural, so once the header is on it will get a ECUTek RaceROM tune there (I cannot rev match for 5hit, and I loved the RaceROM rev match and FFS in my old 86 "RIP") In other, maintenance news, I put some new sparkler plugs in it, and have a new set of DBA Street series pads to put in over the next day or so, I'm running the DBA street series in the SS and Honda and really like them, they work great and are not dusty at all I've also booked in a few days leave over this weekend to give me 4 days weekend do some paint correction and give the leather seats some conditioning and interior some Bissell and steam cleaning OCD lovin', the carpet and interior looks clean, but from my experience with the Bissell IRT carpet, and the steam cleaner IRT trim, looks can be deceiving I've also found that finding a detachable hard top is proving problematic, the main reason why I didn't like the NC initially was the power retractable hard top that I seen them with gave the roof line a weird look, the detachable roof though looks good, and is a same shape as a NA/NB hard top, similar, but unfortunately not the same as it has different fixture point on the front, so fitting a easy to get NA/NB detachable hard top is no bueno New Old cars are fun, cleaning, hunting and playing around brings much joy How are your beasties going? Do you still have the Skyline with the LS???, or Barra??? that you were playing with
    • Unfortunately this new build series will come a car too late for you Mark... However, he does do a wicked MX5 build already you can also check out...    
    • Wow, they are some big images! 🤣 That's quite the intake from Stillen!  Theres 3 things you can use a bed for and one of them is laying out car parts. I love it.
    • Hi all, Bit of an odd question but the only OEM washer nozzles I can find readily available are listed as fitting the R33/R34 models. The R32 (shown below) has it's versions sold as a LH and RH piece while the R33/R34 nozzles are sold as a set (part number B8K30-AA000). Has anyone tried using these nozzles on their R32 Skyline hood? Do they fit without issues or with slight shaving, or are they completely incompatible? Visually they look almost exactly the same as the original factory nozzles I have now. They aren't expensive so I can eat the $30 or so that it would cost to try but I figured I'd ask in case someone had tried it already. Thanks!
    • I'm in the market for 370GT.  I live in Canberra and not much available so I'm looking interstate.  Can anyone recommend an inspection service with expert knowledge of Skylines? Sydney, Melbourne and Adelaide (Elizabeth area)
×
×
  • Create New...