Jump to content
SAU Community

-5's Vs Rs's On A Larger Then Stock Motor

Piggaz

By Piggaz,
in Engines & Forced Induction

 Share

Recommended Posts

  • Replies 261
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

HYPED6
HYPED6

Here is my little story. I have been wondering the same thing the last 6 months or so. This is what I have found. I bought my gtr with plain bearing -5's. Now with Cams, 10.25 @ 292 Good after mar

JAGR33
JAGR33

Did you put your car on a 4wd dyno? That usually shows a lower figure than in 2wd mode. I can understand your frustration but let me tell you this, don't take dyno figures as gospel, they are a tunin

R31Nismoid
R31Nismoid

Nothing I haven't told him on 3 occasions now since Aug 2010, even earlier it think. So basically what you are telling us is that 6 months down the track. You haven't taken it to the track yet? O

Posted Images

Piggaz Grand Master

Piggaz

Posted
  • Author
Posted

Here is my little story. I have been wondering the same thing the last 6 months or so. This is what I have found.

I bought my gtr with plain bearing -5's. Now with

Cams, 10.25 @ 292

Good after market front mount

Very good fuel

Stock dumps

Stock but ported exhaust manifolds

After market exhaust

After market ECU

Fuel systems to support anything I threw at it

Made around 490 rwhp on around 20 psi. Boost control was rubbish. Needed one solenoid per turbo and a 32x32 table just to get any descent control.

If I rung its neck.... (shut the wastegates) it would spike to 2 bar as it came on to boost and 22 psi at 850rpm it would make 530 rwhp. Rubbish.

Now I thought that this was under powered. So made some 2.5inch dumps. No difference

Shortly after one turbo died.

I bought some shiny new -10's.

Made some 3 inch dump pipes. Twin 3 inch front pipe to single 4 inch system.

Engine now makes 400rwhp on 10psi. Much better :)

Bloody thing hits another brick wall at 480 rwhp!!!! Regardless of boost levels. Regardless of ignition timing or fueling etc.

Now. I believe its the standard exhaust manifolds. I really do believe that is the key to making big power out of these turbos.

At the moment I am currently fitting a single turbo charger. Its the only thing I am changing so it will be a reasonable back to back.

Has any one else seen anything else similar?

When my car was on the dyno a few weeks ago we went from 1.7 to 2.0 bar. I made an extra 12 kw (414rwkw) or something stupid so we pegged it back to 1.7 bar. I think my exhuast is too small but also I reckon my head port doesnt match my setup. Its a little lethargic down low but doesnt make mega numbers up top.

Are manifolds stock or port matched. N1GTR's manifolds are standard and makes more power then that.

Those 292 cams are bloody MASSIVE!

GTScotT Grand Master

GTScotT

Posted
Posted

Here is my little story. I have been wondering the same thing the last 6 months or so. This is what I have found.

I bought my gtr with plain bearing -5's. Now with

Cams, 10.25 @ 292

Good after market front mount

Very good fuel

Stock dumps

Stock but ported exhaust manifolds

After market exhaust

Do not just keep throwing money at it. Find a real mechanic if you cannot get the thing to work.

You have not mentioned anything about the motor itself. What sort of head work do you have to support 292x10.25 cams and what sort of motor have you got that would do the 10,000rpm those cams imply?

If the answer is none you have some major issues. I am horrified of the thought of this thing.. I would personally put pencil to paper and plot exactly what I want from it and the setup I anticipate will get me there. I would then pull the motor out and strip it back to a long motor, refitting only parts that suit what I have set out to plan.

No number of band aids, double sided tape, sikaflex or zip ties will stop cut wrists from bleeding out. Get onto a real fix, maybe even start your own thread in the members ride section to properly introduce yourself and the car so you may start an active discussion to help your cause.

It honestly does sound like you have a hungry money pit, see below.

post-43588-0-51473600-1294532701_thumb.jpg

Piggaz Grand Master

Piggaz

Posted
  • Author
Posted

Gav how long have you had your Tomei manifolds on your car? I have been through two sets. Cracks, holes blown in runners and the last set didnt make it to 2000 kms. Alot of that was on E85 (second set) too.

GTRNUR Grand Master

GTRNUR

Posted
Posted

Gav how long have you had your Tomei manifolds on your car? I have been through two sets. Cracks, holes blown in runners and the last set didnt make it to 2000 kms. Alot of that was on E85 (second set) too.

I'd be having a good look at your tune, and your EGT's. These manifolds shouldnt crack if your tune was correct for normal unleadded fuels.

While switching to an alcohol based fuel in theory lowers combustion temps and EGT's, the way many people are setting up their E85 engines with higher compression means the common target afr charts dont produce an EGT that is in the safe range. Ive heard stories of melted exhaust valve guides in alcohol based fuel engines that run compression at the higher end of the scale, so it stands to reason that a moderate increase in EGT's could certainly cause stress cracks in in a manifold.

Piggaz Grand Master

Piggaz

Posted
  • Author
Posted

an amazing difference in midrange!

Damn right it is. If you look up the hot side of the turbo's they are exactly the same.

Gav, were the turbo's modified in anyway or were they straight out of the box and bolted up?

Piggaz Grand Master

Piggaz

Posted
  • Author
Posted

I'd be having a good look at your tune, and your EGT's. These manifolds shouldnt crack if your tune was correct for normal unleadded fuels.

While switching to an alcohol based fuel in theory lowers combustion temps and EGT's, the way many people are setting up their E85 engines with higher compression means the common target afr charts dont produce an EGT that is in the safe range. Ive heard stories of melted exhaust valve guides in alcohol based fuel engines that run compression at the higher end of the scale, so it stands to reason that a moderate increase in EGT's could certainly cause stress cracks in in a manifold.

Thats a good point. My engine is 9.0:1 comp so it is highish. Next time I go back I might mention it to Yavuz (the tuner) and see what he reckons? Either way im back on ported stockers.

Gav Mentor

Gav

Posted
Posted

Gav how long have you had your Tomei manifolds on your car? I have been through two sets. Cracks, holes blown in runners and the last set didnt make it to 2000 kms. Alot of that was on E85 (second set) too.

Actually, I'm not overly impressed with the Tomei manifolds for that reason. I had cracks in the first set that I had welded. Then I found they had burn't through on the outside of the runners. I'm on my second set now and if these fail I'm going back to cast iron units.

On the graph I posted, I did forget to mention I'm running GTS-4 ratios. I'll track down an updated E85 dump graph showing the other set-ups with RPM on the X axis.

Piggaz Grand Master

Piggaz

Posted
  • Author
Posted

Ah already done...

Notice any difference?

It could be placebo but it feels like there is. But that could be just my head. I want to get another set and extrude hone them and really get it spot on! So many people swear by the stockers.... and going by Gav's post above me he has had issues with the Tomei's aswell!

Granthem Mentor

Granthem

Posted
Posted

RPM = (SPEED / 28) * 1000

to work out RPM from a speed based dyno plot, assumes 4th gear with 4.11 diff gears

This doesnt really work for mine, as I doubt my car makes 340rwhp @ 6250rpm. Its more like 7250rpm. Hmmmm.

r32-25t Grand Master

r32-25t

Posted
Posted

It could be placebo but it feels like there is. But that could be just my head. I want to get another set and extrude hone them and really get it spot on! So many people swear by the stockers.... and going by Gav's post above me he has had issues with the Tomei's aswell!

Leave the things alone

Gav Mentor

Gav

Posted
Posted

Gav, were your -5's straight out of the box or were the tinkered with?

With the exception of HKS actuators they are bog stock.

These did need a freshen up with seals and other bits and pieces (maybe bearings) recently after around 5,000 km of mainly hard track time. Still have the same exhaust and compressor wheels 'tho.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R33 GTR running -9 with no tune

      By Duncan · Posted

      Sounds like you've got an interesting adventure ahead here with local support if you have trouble! My guess is that, unboosted, you will be OK with a small upgrade like -9. What will happen is that once the stock ECU sees more airflow than it expects it will add a heap of fuel and pull a heap of timing to be safe because it can't understand how it could get that much air without there being an issue. You will see clouds of black smoke and it won't pull hard through the midrange and top end. So, overall it will be a bit frustrating but should be OK. If you are still nervous set the base timing back 2o through the CAS, but it will be even more sluggish everywhere. As said above through...this is not my guarantee your engine won't be blown into a million pieces, leaving you looking for very hard to find parts A better idea is get a computer with logging ASAP, wire in a wide band O2 sensor and a use remote tuner. I've done multiple cars this way and while it is not as good as a specific tune on a dyno they can get it 90% right. I'd suggest if you can afford an R33 GTR these days you can afford an ECU and tune. And if you can't afford that you sure won't be able to afford the rebuild if it goes bad in the meantime,.  
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yeah it would be nice if someone took the time to put that sort of information together, but there are a lot of variations in looms. I think you are making this way hard for yourself if you just want to get it running....sourcing an SR20 with the right wiring will be a billion times easier than matching the RB loom to an S15 chassis. If you do end up going this way, you just need to trace every wire in the loom with a multimeter, 95% of them will go to a location you can confirm at the ECU.....and then post it up for the next person who needs it  
    • Duncan
      Coolant leak?

      By Duncan · Posted

      Just top it up with water, and keep a general idea of how much you added. It is normal for water to be pushed into and pulled out of the reservoir through the cap, and it should not be more than half full or it will be likely to overflow when hot. Any decent mechanic can do a pressure test of the cooling system to confirm if you have a leak. Keep in mind if it is only leaking a little and when hot it may well evaporate before you see it hit the ground
    • GTSBoy
      Coolant leak?

      By GTSBoy · Posted

      I'd ask the shop what they used and use that. Mixing coolants is sometimes OK, sometimes not, and you have know the details of each coolant to know whether it's a good idea or not.
    • Chupapy
      Coolant leak?

      By Chupapy · Posted

      Is it alright to top up with just another green coolant?
×
×
  • Create New...