Jump to content
SAU Community

Recommended Posts

just wondering how long this motor should last kms etc before i should look at doing something ?? i just bought the car and was wondering thats all cause i dont want to break anything some help would be much appreciated

thanks.

ENGINE: *CP pistons probs more but cant think !!

*Eagle rods

*N1 oil pump

*Tomei sump baffles

*Tomei headgasket

*Tomei oil feed restrictors

*custom oil drian from the rear of the head to the sump

*balanced crank

*acl race bearings throughout

*N1 water pump

*Apexi cams ( not sure what lift)

*Aftermarket vavle springs

*Hks cam gears

*Hks timing belt

*Bigger Fuel pump

*700cc sard injectors

*adjustable fuel reg

*Nisstune ECU

*twin Garrett 2860-5s

*Huge intercooler

*Alloy radiator

*Front sway bar

*middle sway bar ( in photo of interior)

*rear sway bar

*Bilstein coilovers

*torque split controller( not working at the moment will try to get fixed before sale)

*drilled rotors

*gauges, oil pressure, boost

*Alpine headunit

*Alpine 6x9s

*oil filter relocation kit

Edited by danny14
Link to comment
https://www.sau.com.au/forums/topic/351052-32-gtr-forged-engine/
Share on other sites

If it was built right it should last as long as your usage implies.

If you pump your -5s to max capacity and run it on the knifes edge on the track every day of its life, you will get about as long a life span as you would any other race motor before it needs rebuild (not very long at all). Yet if you were to daily it and take exceptional care of it I anticipate it would possibly last as long as a factory built motor.

I would probably change that N1 oil pump to a Nitto or JUN item though, that is the weakest link at present.

The only way to know would be to strip it down which kind of defeats the purpose.

Who knows it could have been slapped together on the grass in someone's back yard with all the tolerances wrong and it might last a week, it could have had everything done perfectly at a shop and then run with no oil, or everything could be fine and it could last 100,000kms?

the speaker part was not ment to go in i just pasted and copied page lol...

the oil pump is it really a problem i drive it maybee 3 times a week and i dont thrash it everywhere i go. everything feels tight

it currently makes 314 kw but has made 450 kw with the old ecu that was pfc it now has a nistune because of defect

well.. if its lasted 3 years and is still running sweet today, not burning oil etc, im sure its been built some sort of standard - but as said earlier, it could go bang 2moro or could go for another 5 years - too many variables!

ok apparantly it didnt... saysss im just goin off what the original owner that built it from ice performance told me................................ thats all im not making up shitttttt if thats what u think

do u have any proof that the engine is even built? or did he just hand u receipts from when his friends, friends built a motor.

common misconception is that building a motor gives u fully awesome big power, when all it does is make the engine components stronger.

sure u can make 650rwhp and the motor will last 12months or you can run the same motor at 300rwhp and last 10years

  • Nope 1

do u have any proof that the engine is even built? or did he just hand u receipts from when his friends, friends built a motor.

I'd be thinking a similar thing.

If it was from ICE down here in Vic, I'd be even more worried... There were plenty of no-so favourable experiences that myself and several friends went through before they shut doors.

ok apparantly it didnt... saysss im just goin off what the original owner that built it from ice performance told me................................ thats all im not making up shitttttt if thats what u think

Defensive much? Perhaps those posters are thinking that whoever told you it made 450 is a liar, and therefore you cannot trust anything else this person has said to you.

Also

*middle sway bar ( in photo of interior) <= WTF??!!

*torque split controller( not working at the moment will try to get fixed before sale) <= if the controller doesnt work it will be taily but still put torque to the front wheels. If it doesnt, it could be expensive to fix.

*drilled rotors <= likely to crack with track use

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...