Jump to content
SAU Community

Recommended Posts

hai guise, was wondering if there are any home tricks to checking the state of the intake? IE if there are any air leaks?

or do i need to take the car to a shop for them to pressure test it?

cheers

Edited by Clutch
Link to comment
https://www.sau.com.au/forums/topic/351535-intake-leak-test/
Share on other sites

I made up a cheap one with some pvc pipe caps and a $20 hand pump. See below photos. I blocked off the pipe going into the throttle body, hooked up the pump to where the pod filter was and pumped away.

The advantage of the hand pump over an air compressor is that because it is quiet it is very easy to hear even the smallest leak.

Do you mean the intake manifold or intake piping? Mine was for the intake piping.

post-29432-0-01090900-1295839930_thumb.jpg

post-29432-0-80208500-1295839934_thumb.jpg

post-29432-0-91684800-1295839940_thumb.jpg

If you get a can of Aerostart or similar and spray it around while the car is idling it should raise the revs if theres a leak as it will suck it in. Perhaps not as good as the method mentioned above but if your looking to do it without spending to much that would be the the way to go

To check for a leak in intercooler, piping or around silicon joins, etc spray with soapy water, preferably while at a high idle (1500-2000rpm is plenty).

If you have a leak it will blow bubbles.

Seems wierd & you may think the water would get sucked in but it works...

Another good one is to remove your pod / airbox so you have access to the afm and while the car is idling cover the afm with your hand so no air can get in.

Then you should be able to hear the hiss of where the air is getting into the intake.

if you have a leak as well, you should blow a small amount of black smoke on boost. some of the air will escape the intake piping, but since it's still being measured by the AFM the correct amount of fuel will be going in as though there wasn't a leak.

Unless you're running a MAP sensor like me. then you're screwed for this idea lol

yes. If the leak is big enough in your case, you'll be sucking in air that hasn't been measures by the AFM while idling or off-boost. This will cause you to run lean, and missfire like a 14yr old boy at a wet T-shirt comp.

Damn you!

I read this thread a couple of hours ago and thought hmmm maybe i'll go look over my intake to see if I have any leaks. Turns out I have a leak coming from under the plenum where the damn gasket has slightly blown out.

God damnit!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Kapr Haha yeah thats the one. I missed that you had a built up engine, I wouldn't want to run it on there either then. It was good in my situation just to replace the original turbo on a stock engine. @MBS206Yep definitely not a replacement for anything name brand
    • You are selling this? I have never bought something from marketplace...i dont know if i trust that enough. And the price is little bit "too" good...
    • https://www.facebook.com/share/19kSVAc4tc/?mibextid=wwXIfr
    • It would be well worth deciding where you want to go and what you care about. Reliability of everything in a 34 drops MASSIVELY above the 300kw mark. Keeping everything going great at beyond that value will cost ten times the $. Clutches become shit, gearboxes (and engines/bottom ends) become consumable, traction becomes crap. The good news is looking legalish/actually being legal is slighly under the 300kw mark. I would make the assumption you want to ditch the stock plenum too and want to go a front facing unit of some description due to the cross flow. Do the bends on a return flow hurt? Not really. A couple of bends do make a difference but not nearly as much in a forced induction situation. Add 1psi of boost to overcome it. Nobody has ever gone and done a track session monitoring IAT then done a different session on a different intercooler and monitored IAT to see the difference here. All of the benefits here are likely in the "My engine is a forged consumable that I drive once a year because it needs a rebuild every year which takes 9 months of the year to complete" territory. It would be well worth deciding where you want to go and what you care about with this car.
    • By "reverse flow", do you mean "return flow"? Being the IC having a return pipe back behind the bumper reo, or similar? If so... I am currently making ~250 rwkW on a Neo at ~17-18 psi. With a return flow. There's nothing to indicate that it is costing me a lot of power at this level, and I would be surprised if I could not push it harder. True, I have not measured pressure drop across it or IAT changes, but the car does not seem upset about it in any way. I won't be bothering to look into it unless it starts giving trouble or doesn't respond to boost increases when I next put it on the dyno. FWIW, it was tuned with the boost controller off, so achieving ~15-16 psi on the wastegate spring alone, and it is noticeably quicker with the boost controller on and yielding a couple of extra pounds. Hence why I think it is doing OK. So, no, I would not arbitrarily say that return flows are restrictive. Yes, they are certainly restrictive if you're aiming for higher power levels. But I also think that the happy place for a street car is <300 rwkW anyway, so I'm not going to be aiming for power levels that would require me to change the inlet pipework. My car looks very stock, even though everything is different. The turbo and inlet pipes all look stock and run in the stock locations, The airbox looks stock (apart from the inlet being opened up). The turbo looks stock, because it's in the stock location, is the stock housings and can't really be seen anyway. It makes enough power to be good to drive, but won't raise eyebrows if I ever f**k up enough for the cops to lift the bonnet.
×
×
  • Create New...