Jump to content
SAU Community

Recommended Posts

so, it could be anything?

sigh

guess ill take it to a mechanic

Idle and missfire problems are always the most fidly to diagnose as there are so many things that could be causing the problem.

I'd be going to a mechanic as well bro.

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Idle and missfire problems are always the most fidly to diagnose as there are so many things that could be causing the problem.

I'd be going to a mechanic as well bro.

the only reason i havnt gone to a mechanic yet is because it wont be something simple that they can diagnose quickly, i will be up for a hefty check because they will have to spend a fair amount of time checking everything

Edited by Clutch

my rb 25 s13 starts the same way sometimes up to 2.5 k rpm........ its always done that since i can remember.. it has nothing to do with fuel pump ..got new walbro 255.....

could it be bad timing?

cold start valve? what is that and where is it loated....?

possible factor, would this also cause heavy fuel smell while driving sometimes? how do i check that my fuel pump is working properly?

You didnt specify at what times you were gettng the heavy fuel smells, so I assumed while boosting. Does it smell like there is a fuel leak somewhere? Is your fuel economy really bad?

I highly doubt it is a TPS issue. Try resetting the ECU (If it is a stock ECU) purely because this is a simple test to do.

But if you want to see if its a TPS issue, I think unplugging the TPS will put it into base idle mode anyway, so it will idle without the aid of the ECU (as far as I remember). This mode is usually used to adjust your idle to get it to sit right, so if you unplug the TPS and your idle stays high then it might be an issue with how your idle is adjusted (eg. it is adjusted to high and your computer slowly brings it back down to an acceptable level

Give that a go

I'm not as familiar with R32's as I am with R33's but I think this was discuss a while ago (when talking about adjusting idle) and on the 33's you have to unplug the TPS to get it into base idle mode, but I think the R32's you had to unplug the AAC valve instead to get it into this base idle mode?

I've seen R33's with there TPS not even plugged into anything that still run fine (This is going back a while) so I guess they are much more dependant on the Air flow then throttle position to run

Edited by 89CAL

ill check it out and clean it , see if it makes a diffrence....and sometimes my car iddles freakin wierd ...honestly im pretty sure its throwing codes but my ecu light has been riped out ..or something ....when i bought the swapt to put in my s13 the ecu never had a light on it......so i dont know how to check for codes....but it runs good besides sometimes for a split sec when going steddy spedd it cutts off causing a tugging sensation....and when i fully gun it theres a flat spot 5 threw 6 k rpm....i have to let of the throttle half ways and it feels like it acutally goes better that way then fully gunning it.??? but thats another issue now back to the iddle problem....

any pics of how the cold start valve looks like?

o and sometimes my car smells like fuel ...not all the times just at certain times it tends to....lol and i get about 320 miles to the s13 tank..is that bad? sorry for going off topic......

Ok so that depends on if it's raw fuel leaking somewhere or if the mixture is becomming rich

Fuel leak is pretty straight forward. I know vs commodore urea get a blocked breather and certain times fume the cabin with fuel lol

Running rich will either be ECU or tune issue. Or air leaving the system after it has been through the afm. So this would occur only on boost if there was a leak or with an atom bov. At Least that's all I can think of ATM

Any more info you can give?

Did you replace the o ring when you did the pump as soon as you remove the inspection panel that o ring swells and does not seal properly and I got a cas from the wreckers for 80 bucks there like 500 or some ridicouls price like that brand new it's only a 10 min job to replace hard part is making sure your timing is correct afterwards you need to put a light on if or hook up a consult

i think the o ring was a bit loose, so i tightened that up

when i started the car up without the plug at the bottom of the tps plugged in, it idled at 1500 or so, when i plugged in it went to normal, and then i unplugged while the car was running and the car stalled

does this all sound like normal behavior?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I can ship Nismo floor mats to you: https://www.oemsoko.co.jp/products/nismo-floor-mats-for-skyline-r33-bcnr33-stagea-wgnc34?_pos=1&_sid=9278c1467&_ss=r  
    • Here's the link: https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6642/misc/G49?frame_no=WGNC34-137122 What you think about it? The same product i found on nengun: https://www.nengun.com/oem/parts/40567/MiPwn5qAMfCfmpxHNDnwn5q9MDAx8J-QiW9sZC1qcC0xMTAtRzQ5LS0wMDE/Floor+Carpet+%2F+Mat+2/0688339eba149c19 Bot i have spoken to 😅 ensured me, that mats are 100% original, oem product. I have my doubts. I also heard what you mentioned, that nengun often offers items that are actual not available... On the other hand mats i found on japanese yahoo or ebay are in poor condition and still quite expensive so i'd rather wait for some better offers. My location - Poland. We literaly don't have ANY market for used Stagea parts so need to search outside Europe.
    • You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
×
×
  • Create New...