Jump to content
SAU Community

Recommended Posts

Hey guys, I'm new to the R34 world. I drove a GtiR up until i put to much work in her and she become silly for everyday driving. Anyway I've had my 34 for about 6mths now and i only seem to get about 320ks to a tank. Is this standard ? I'll post details below. Anything you think could help my thirsty beast :P would really help!

Petrol: Shell Optimax or any 98ron

80,000 Service 3mths ago

Mods: 3" exhaust from the turbo back

Apexi twin air filter intake

Boost set to 12

PS: I thought i have been driving her very respectably. I blow her nose every now and then for good health but that's all.

Thanks Guys :)

post-79360-0-84033700-1297806375_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/354105-fuel-consumption-on-r34/
Share on other sites

Apexi twin air filter intake? Do you own a GTR?

If you're only getting 320km, then I would highly recommend cleaning your Air Flow Meters (AFM's) and replacing the o2 Sensors. I've recently done this and it's made a world of difference to both fuel economy and performance.

See this article about replacing your o2 Sensors: http://wardiz.org/blog/2009/07/30/replacing-an-oxygen-sensor-on-a-r34-gtr/

A couple new sensors will set you back about $176 incl. delivery.

For the AFM's, get some "CRC Air Flow Sensor Cleaner" available at Supercheap or Autobarn: http://www.supercheapauto.com.au/online-store/products/CRC-Mass-Air-Flow-Sensor-Cleaner-300G.aspx?pid=157339#details

The cleaner will set you back about $23 per can. The AFM's need cleaning every now and then because oily residue builds up on the sensor components. This is cause by the "blow by" gas from the cam cover.

I filled up this morning - 315km from 50L - I exclusively use 98RON fuel.

That sort of fuel economy is normal for me - my driving is purely city driving (no more than 10-15minutes, never more than 60kph, lots of stop start, aircon on all the time, and I'm pretty heavy on the accelerator). Last big highway drive I got 500-600km from 50L.

Mods include 3" turbo-back, K&N panel, FMIC & 10psi wastegate actuator - dyno run was 182rwkw (pre-10psi actuator)

I'm currently at 105,000km and I changed my o2 sensor - with a genuine nissan one - at 80,000km (as per 80,000km service guidelines). My fuel economy didn't really change before/after o2 sensor change. As part fo my 100,000km service I fitted new plugs, new coil packs, new timing belt, new thermostat, new water pump, etc. I've also recently serviced (cleaned) my AFM - it's worth noting that none of this seems to have affected my fuel economy.

Purely as a check, find out whether your o2 sensor was changed as part of the 80,000km service (it is one of the bigger items listed, along with your ancillary belts).

All in all, you're getting similar economy to me - so sounds fairly normal.

I'm planning on getting my nistune tuned soon and trying to get some economy back - I know it's running quite rich (which is also fairly normal for a modified car without ECU tuning)

Thanks Owens, thats a good idea on the o2 sensors. I really wasn't sure what milage i would get from a GT-T, if that's all your getting JRM maybe with a bit of maintenance i can get her up closer to the 400k mark.

Stupid question; Do intercoolers really improve fuel economy ? I understand the argument that cold air is denser than warm but the space is the same.

I think the main consideration to make is that the standard ECU tuning is - by default - going to richen the mixtures when you modify the car. This is a protection mechanism built in there by the Nissan engineers - richer mixtures are less likely to have detonation, and act to 'cool' the combustion process more - making it much safer for the engine.

I honestly expect my fuel economy to increase fairly dramatically once it's been tuned as they'll make an effort to keep the mixtures more at optimum levels at different load-levels.

how about you take note of how many L's you are putting in instead of just saying "a tank" as that could mean 45L or 65L, or if your fuel gauge is totally fubar'd, 25L. work out your fuel economy into a L/100kms form then you can see exactly how bad your economy is. if you do mostly highway driving and your economy is over 10L/100kms then your o2 sensor needs replacing. if you do mostly city driving and give it the beans a fair bit then you may see anywhere up to 17L/100kms and replacing the o2 sensor won't do a thing since it only used by the ecu on light throttle. if you drive it normally, but do a lot of stop/start driving in traffic then you could see anything from 12L/100kms up to 14L/100kms, it really does depend.

one thing to pay attention to is how long your car takes to come up to temp. if the needle isn't to the centre of the gauge within 5 mins of driving then you need a new thermostat and that should help with economy. also, if you are one of those people who let the car idle until it is up to temp before driving off, then that will be making your economy worse, plus it is a waste of time and fuel and it can actually cause more wear on the engine than driving like a grandma straight away.

Seriously just putter around in any turbo like it was a 4cyl n/a and you will get fuel economy even if you have standard ecu with rich mixtures. I had my mother drive my s2 r33 gts-t with light mods and she got better fuel economy than me because it comes down to your right foot.

My dead stock (everything) R34 GTT on the dyno at 126,000km had AFR's starting from 11.8 going to 10.2 at the top end (ie, ridiculously rich)

I will eventually be installing a Nistune board and getting it remapped to neaten that fuel map up to be a little more reasonable.

My dead stock (everything) R34 GTT on the dyno at 126,000km had AFR's starting from 11.8 going to 10.2 at the top end (ie, ridiculously rich)

I will eventually be installing a Nistune board and getting it remapped to neaten that fuel map up to be a little more reasonable.

that isn't that bad. mate of mine had a 32 on his dyno that went off the scale (think the lowest the wideband went to was either 9 or 10) and then left a big black wet patch on the wall behind the dyno. it was pretty much pissing out raw fuel, LOL.

also what the car runs are full throttle has little to do with fuel economy when driving sensibly. when you are only using light throttle (accelerating gently or at a steady speed), if your o2 sensor is working properly then your AFR will only be around 14.5:1. this is because the ecu is in closed loop mode and it uses the o2 sensor. if you press the accelerator down more then it may jump out of closed loop mode and it goes back to the ecu mapping (and ignores the o2 sensor) and the AFR's will jump down to around the 11 to 12 range (depending on what rpm you are at).

some people try to get better fuel economy by not reving the car out past a certain rpm range. this helps, but if you use 50 or 60% throttle below that rev range you will still get average fuel economy. you can rev up to 6000rpm with only low throttle (lets say 15%) and get better fuel economy than someone in a higher gear that is using 60% throttle and only reving to 3000rpm. but then at the same time, cruising along at a steady speed it can be better to use a higher gear and a fraction more throttle. i did a test with a consult cable on the missus pulsar. on dead flat ground at 60kmh 5th gear got 10% better economy than 4th, but the moment you got to the slightest incline 4th gear was a fraction better, but they were both better than 3rd gear.

that isn't that bad. mate of mine had a 32 on his dyno that went off the scale (think the lowest the wideband went to was either 9 or 10) and then left a big black wet patch on the wall behind the dyno. it was pretty much pissing out raw fuel, LOL.

also what the car runs are full throttle has little to do with fuel economy when driving sensibly. when you are only using light throttle (accelerating gently or at a steady speed), if your o2 sensor is working properly then your AFR will only be around 14.5:1.

Quite valid points, however, I get the feeling that 32 wasn't in completely factory spec (from airbox snorkel through to exhaust tips).

I do intend to check that 02 sensor out, I did specifically ask the guys at the time to check it for me, and they said it was ok, but I never confirmed that myself.

  • 4 years later...

I filled up this morning - 315km from 50L - I exclusively use 98RON fuel.

That sort of fuel economy is normal for me - my driving is purely city driving (no more than 10-15minutes, never more than 60kph, lots of stop start, aircon on all the time, and I'm pretty heavy on the accelerator). Last big highway drive I got 500-600km from 50L.

Mods include 3" turbo-back, K&N panel, FMIC & 10psi wastegate actuator - dyno run was 182rwkw (pre-10psi actuator)

I'm currently at 105,000km and I changed my o2 sensor - with a genuine nissan one - at 80,000km (as per 80,000km service guidelines). My fuel economy didn't really change before/after o2 sensor change. As part fo my 100,000km service I fitted new plugs, new coil packs, new timing belt, new thermostat, new water pump, etc. I've also recently serviced (cleaned) my AFM - it's worth noting that none of this seems to have affected my fuel economy.

Purely as a check, find out whether your o2 sensor was changed as part of the 80,000km service (it is one of the bigger items listed, along with your ancillary belts).

All in all, you're getting similar economy to me - so sounds fairly normal.

I'm planning on getting my nistune tuned soon and trying to get some economy back - I know it's running quite rich (which is also fairly normal for a modified car without ECU tuning)

G'day mate i notice your running a k&n panel filter i run the same filter but only just put it in a few months ago how much attention should i pay to my air flow sensor? (i.e how do you deal with the oil off the panel onto your sensor) i have heard this can be an issue but more often than not its perfectly fine i just dont want to run into any issues further down the track so if you could give us some maintenence advice or a bit of a guide it would be much appreciated thanks mate

i only seem to get about 320ks to a tank. Is this standard ?

f**k no! It's terrible. unless you are doing major stop-start driving you should be getting between 12 and 12.5L/100km (so 50L will get you 400km). On the open road it should be in the 10's.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Apologies for the long post, but needed somewhere to lay out the entire timeline of events and actions taken:   I've got an 89 GTR with a R34 RB in it. It's been running great all year, driven probably 500KM in the last month. It's not my daily driver, just a weekend fun car.    Build info: R34 RB26 - HKS 2.7 stroker kit, HKS adjustable cam gears, HKS turbo upgrades, Trust intercooler, R34 factory DENSO 440cc injectors, JUN chipped/tuned R32 ECU. All of this work was performed in Japan back in 2019.    Thursday 10/2/25 - It's a nice day and decided I'll drive it to work, I start it up in the garage and I notice it took a few extra cranks and sounded a bit funny. I figure maybe it was just because it was a pretty chilly morning. I pull it out into the driveway to warm up a bit before leaving. As I leave the driveway, it feels very off and sounds like a misfire. I pull it back in the garage to deal with after work and take the daily to work. I was able to diagnose it as a cylinder 5 misfire with the old spark plug test (unplugging each plug until a sound change with the engine running). I take off the whole ignition system, ignitor, plugs, spark. *Important note, it is still on the R32 ignition system with the separate ignitor system. I test each system with a multi-meter and nothing presents as a smoking gun. I put it all back together and it starts up no issue. I go ahead and order the PRP R35 ignition conversion kit. It should arrive today (10/13/25)   Friday 10/3/25 - Another nice day, car starts up great and drives great all day. Very pleased that everything seems to be OK   Sunday 10/5/25 - Decided I'll take it to play some golf, load up and drive to the course about 25 minutes away. Drives wonderful the whole way there, I pull in the parking lot and the engine completely comes to a stop. I do not recall if it sputtered at all, but just remember all of the sudden the engine was off. I roll it into a parking spot, try to crank it back on and nothing.  It'll crank and crank and not even try to start. End up getting it towed back to my house and push it up into the garage.    Items I have checked: Fuel in the tank Fuel Pump relay Fuel pump fuse  Spark Plugs & gap Coil packs Ignitor    I know the cylinders are getting fuel as the plugs smell like fuel after a start attempt. I tried spraying starter fluid into the manifold and cranking and not even a sputter.    I decided to do the live CAS test (removing the the CAS, ignition on and spinning the CAS stalk to see if the injectors pulse and spark is active). All of the injectors were pulsing and I have spark at the plug. The half-moon end of the CAS did seem very loose, I'm not sure how much play is supposed to be there, but it was more than I expected. There was no in/out play of the shaft, just the tip end that is pinned on had quite a bit of play.    CAS Play video   When I put the CAS back in, I stupidly did not re-time the engine. I know I need to do that tonight, however, I do not think it will start given it seemingly was not the issue. My plan is to do the PRP R35 coil kit and retime the engine at the same time.    I plan on ordering the Haltech Nexus Plug-in ECU once they are available again, but ideally would like to get this sorted before firing the parts cannon at it and potentially adding more variables.    Anything glaring that I am missing here, I'm a bit at a loss?          
    • Get it on a dyno. Get something logging Consult. Run it up and find out what is causing it.
    • Looking for a plenum for rb25 de+t neo  Not looking to push much power maybe 300kw at the wheels, is there much difference in flow for Freddy “Greddy style” compared to original Greddy or options like Proflow or Otaku garage?    I won’t be porting the de Neo head for now as I think it’ll be fine 280-300rwkw but appreciate the help and any experiences anyone has between them and any advice. Thanks  Looking at this plenum for now below 
    • engine wise almost no mods: stock ecu Greddy front mount intercooler Greddy forward facing intake w R33 TB stock fuel system, stock injectors, rail etc. Kakimoto racing hyper 3 inch exhaust system Apexi intake filter New NGK –R BCPRES (.8 gap) plugs  
    • Nice one @Pac - looks like a fair few 1600's there! 
×
×
  • Create New...