Jump to content
SAU Community

Recommended Posts

Hey guys,

Looking to get my limiter fitted before the next DECA but am unsure where to go as the instructions are entirely in Japanese, and it would probably require someone who knows the Supra wiring loom.

Also I'm aware this does NOTHING for my car, if anything probably puts the engine at more risk, but f**k it. I want to go to a couple of DECAs with a straight pipe, ignition cut and make some noise. After a few events I'll pull it out and sell it.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/354648-who-can-fit-a-beer-rev-limiter/
Share on other sites

Come on it can't be that bad for the car. From what I've read its not worse than bouncing the limiter off the normal fuel cut (which admittedly is pretty bad anyway). I'm not going to sit there bouncing for shits and giggles, it'll just be when I hit the limiter as we all do at DECA, only this time with noise and flames.

Plus its a healthy stock NA 2JZ, nearly impossible to break one of those.

P.S. Thanks for the info on Edge, I'll call them tomorrow.

no, it's not the same as bouncing off the stock limiter at all. there are MANY people that have lost motors due to these things

it's an ignition cut limiter, hence the bangs.

the main cause of engine failure is a dead oil pump from the vibrations caused by the bangbangbang, which as you can imagine is not the best thing to happen while you are redlining it.

Fair enough, thanks for the warning. I always assumed the problems came from unburnt fuel passing through a white hot turbo and potentially detonating in there. Meaning my NA would be relatively safe from that sort of problem.

Shame though, would've been a lot of fun.

Do you? im yet to see any, spend more time with the car parked at a kabab shop with the autosalon crowed

Who the f**k are you? Since I don't know you and you drive old pieces of shit your comments mean nothing to me :)

  • Like 1
  • Nope 5

HAHAHA I love how he comments on my car right away, with out knowing what i drive, And it not hanging shit he said his car shoots flames i have seen him/it around and yet to see flames and most times i see the car on a Friday night it parked at the kebab joint.

Sorry if i hurt his feelings but just stating what i have seen

  • Like 2

Also I'm aware this does NOTHING for my car, if anything probably puts the engine at more risk, but f**k it. I want to go to a couple of DECAs with a straight pipe, ignition cut and make some noise. After a few events I'll pull it out and sell it.

Cheers.

Not 100% True a friend with r31 Stock as a rock sept for a upgraded clutch and welded Diff and a Bee-r got 5mph Better using it for flat shifting then his old PB other then that it prob useless i would have gone with the Gizzmo launch control that does the same things there is a vid on fullboost somewhere of my old evo 6 running it

HAHAHA I love how he comments on my car right away, with out knowing what i drive, And it not hanging shit he said his car shoots flames i have seen him/it around and yet to see flames and most times i see the car on a Friday night it parked at the kebab joint.

Sorry if i hurt his feelings but just stating what i have seen

Well you don't know me. And never seen me drive. Sonit would be quite clear that you haven't seen shit. My car is parked at bp for no more then 10 minutes till we fuel up and leave and meet up with mates. Are you one of those guys that rocks up on a Friday night alone and goes driving up and down

  • Like 1
  • Nope 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...