Jump to content
SAU Community

Recommended Posts

im thinking of getting my 32 diff welded so its always locked and its my daily but is all the storys true that it can snap. knocking noise when taking full lock turn. ?

or to get a 2 way which is hard to find in 6 bolts ?

Link to comment
https://www.sau.com.au/forums/topic/355620-to-get-my-diff-welded-or-get-2way/
Share on other sites

If it's your daily and you're worried about all that stuff, then just shim up your stocker.

Or..

Don't be a pussy. My 32 was daily driven with a button clutch and 2-way for a couple of years.. good times :ermm:

Try driving an N/A, RWD, 1 tonner V6 Rodeo.

That thing comes with a locked diff as standard, chirps out something mean and is an utter death trap in the wet! In the dry though that thing is awesome fun.

I'd say your mild manned N/A would be safe with a cheap weld!

Try driving an N/A, RWD, 1 tonner V6 Rodeo.

That thing comes with a locked diff as standard, chirps out something mean and is an utter death trap in the wet! In the dry though that thing is awesome fun.

I'd say your mild manned N/A would be safe with a cheap weld!

i assume you mean to say it has a factory fittled LSD.

Locked diffs are illegal for street use, so i highly doubt your car has a factory locker. (reason being, they promote understeer when small throttle inputs only are applied.)

Imagine that nanna jenny gets in her hubby ute... she goes down to the shops but being elderly and irratic in her driving she comes straight off the throttle and turns hard and late at the first corner she gets to... now if there is no throttle then how is the inside wheel going to break traction to spin at constant speed with the outside wheel when turning.... it wont. it will want to push the car in a staright line.... see what im getting at.

this wont be the case in all chassis or road conditions. both my 33s have had locked differential and i have not had those problems but in other chassis it is a problem.

But it may well be a very tight lsd. Most decent four wheel drives and utes come standard with or are available with a farely heavy duty lsd.

  • Like 1

i assume you mean to say it has a factory fittled LSD.

Locked diffs are illegal for street use, so i highly doubt your car has a factory locker. (reason being, they promote understeer when small throttle inputs only are applied.)

Imagine that nanna jenny gets in her hubby ute... she goes down to the shops but being elderly and irratic in her driving she comes straight off the throttle and turns hard and late at the first corner she gets to... now if there is no throttle then how is the inside wheel going to break traction to spin at constant speed with the outside wheel when turning.... it wont. it will want to push the car in a staright line.... see what im getting at.

this wont be the case in all chassis or road conditions. both my 33s have had locked differential and i have not had those problems but in other chassis it is a problem.

But it may well be a very tight lsd. Most decent four wheel drives and utes come standard with or are available with a farely heavy duty lsd.

+1

definitely heavy duty lsd then haha

yup. and its sooo much better than having a 1 tonner with an open center...they see a hill or some grass and just cock a leg and go nooo where.

yer of corse. many cars would be useless without lsd but from factory the lsds start to lock up upon acceleration.... not deacceleration.

track cars... yer grab a 2way lsd or a locker. in a drift car its good for obvious reasons and in a circuit car you usually getting ready to get back on the power by the time ur at the apex. also there generally isnt trees or power poles at a race track lol and u have better rubber on the car so the front has half a chance at fighting understeer. (but better rubber at the back can also increase its tendancy to 'drive straight' if rear is locked.)

by 6 bolt does it have 6x1 or 3x2 pattern?

cheers everyone.

thats very unlucky for ur mate.

yes its 3x2 .

and so what if its non turbo big deal your car might beat me on a straight but "Men with guts attack those corners!"

yeah just checked mates his welded diff has been fine.

because a 1.5 way is not predictable to a 2way or, welded always predictable.

  • Nope 1

yer of corse. many cars would be useless without lsd but from factory the lsds start to lock up upon acceleration.... not deacceleration.

track cars... yer grab a 2way lsd or a locker. in a drift car its good for obvious reasons and in a circuit car you usually getting ready to get back on the power by the time ur at the apex. also there generally isnt trees or power poles at a race track lol and u have better rubber on the car so the front has half a chance at fighting understeer. (but better rubber at the back can also increase its tendancy to 'drive straight' if rear is locked.)

A 2 way (even a tight 1.5 way) will push the car into understeer. A locked diff is worse. Much worse.

and so what if its non turbo big deal your car might beat me on a straight but "Men with guts attack those corners!"

yeah just checked mates his welded diff has been fine.

because a 1.5 way is not predictable to a 2way or, welded always predictable.

That is nonsense A 1.5 way is as predictable as a 2 way. It also allows the car to handle a whole lot bettr because the diff doesn't have the same propensity to lock on the over run.

Bottom line: dont run a welded diff on a road car. Not only is it illegal, it is dangerous.

Edited by djr81
  • Nope 1

honestly, i have had a car with a welded diff, and i have driven a number of other with them, and i never had a problem with it on the streets )apart from the skipping noise when doing a tight turn around cops ;))

i do however agree that a propper 1.5 or 2 way is 100 times better, but i'd rather have a weldy than a single pegger!

as long as you are aware of it, then there should be a danger, just dont give the car to the mrs ;)

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
×
×
  • Create New...