Jump to content
SAU Community

Recommended Posts

nah defo not trapped air in there.. have bled it properly til no bubbles coming out the bleed screw.

nothings changed either,.. and the problem has got worse over last few events so something is up

Get the gas test done on the coolant to confirm HG. It's the easiest way to rule it out.

With the problem getting progressively worse it seems pretty likely.

Running E85 is probably helping to keep your temps down as well....

Probably wouldn't hurt to under drive the water pump either.

Edited by badhairdave
  • Replies 80
  • Created
  • Last Reply

Top Posters In This Topic

I've had similar issues in the past with cheap radiators. My first one clogged up with shit and did the same as what you are describing.

Take the rad out, put a garden hose on one end and let it rip. If it flows fast, you have other problems, if it doesn't get a new rad. (Thanks to Trent for that)

done pressure test on radiator.. 15psi for 5 mins and no drop in pressure

comp tested with works ryco comp tester which does read lower then most

1: 90

2: 90

3: 90

4: 95

5: 95

6: 90

Shouldn't it read the same as most? If you have 90 compression, you have issues

Is it losing any water at all?

I had a headgasket issue last year, leaking into the cooling system it displaces the water and leaves you with air.. try getting it on dyno and watching the overflow tank when it hits boost. I did the same test you did by checking for leaks up to 20psi and it was fine while idling in the car park. Watch it come on boost though and suddenly the overflow tank starts bubbling violently.

If you haven't got a dyno to test on, just take the overflow pipe off the overflow tank and poke it outside the bonnet and go for a run. You'll soon see it go off like a pressure cooker.

Do you still have the factory oil cooler?

what are your oil temps doing?

I have the same issue with my CA, couldn't keep it cool even with a 150% thicker radiator (25mm R32 Vs' 10mm Standard CA). Once i fitted a oil cooler never had an issue again.

Mt theory is that the only way that the engine could get the heat out of the oil is through the coolant.

i have an aftermarket oil cooler (and still the OEM near the filter block) and oil temps reach 130 ish after hard laps.

not really losing water... it doesnt use it. it pushes it out the rad once boiling and doesnt suck it all back in.

i always thought that was typically an air leak ie pushes water out but sucks air back in, but you've had a pressure test. maybe the rad cap is the problem and letting water out but sucking air back in. HG as suspected might explain why the water is being displaced.

Edited by Scooby

You still havent answered the question as to what type/thickness FMIC youre running.

Have you made any effort to ensure all airflow actually travels through the rad ie sealing and cowling of the radiator to the rad support???? Same with the oil cooler?

Any type of cooler works 1000% better with ducting/cowling.

It appears the car is mostly used for drift??? You need to make the most of the little airflow you get...

Again a pressure test shows absolutely nothing about the cooling ability of the radiator.

sorry mate missed your post.

its a 400X300X76 core mounted right in front of the rad. reason for this was to run shorter cooler piping and have the cooler in a safer position then the tradiational fmic location.

i have made an alloy box section up also which directs aii the air coming in from the front bar thro the IC and rad.. the sides are blocked off so it is un able to go anywhere else.

183152_1764592067976_1034359196_1948264_812334_n.jpg

183608_10150098000211109_693631108_6607544_2048564_n.jpg

Well Snowy is running a triple pass PWR items ATM i believe. So far so good.

Looks like that front bar is smaller than the ducting?

Also what is on top where the rad support is? If there is no panel, all the air is gonna do is go that way as it'll look for least resistance.

Or simply go around the sides. Also how much room between I/C & Rad?

Perhaps just take a photo looking down onto it

What cooler is right @ the bottom of the I/C?

front bar and duct are a snug fit, same size. the sides are the same width as the rad.. air is forced thro the cooler and the rad. the IC is 5mm away from the radiator. no top panel. should probably make one up.

the little cooler at the bottom is a power steering cooler.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Slow when hot could also be because its getting more dynamic compression, OR things are getting a bit tighter once it is all expanded. If it were an earthing issue, typically I'd expect you to have it have issues all the time. Unless it's really a combination of both things. Where the higher compression, and things being a bit tighter, is giving that bit of extra load and you do need a slight clean up on the cables/connections.
    • Yeah, this is one of the most annoying things about nissan part numbers... I've got an unrelated example... Image is of the AT output shaft ~ they have the same part#, but clearly the shaft on the left is beefier design to that on the right ...the difference (essentially) is the 'lighter' shaft on the right, is for engines up to RB25DE (this includes RB20 variants) : the shaft on the left is for RB25/26DET(T)....are they interchangeable? Yes...but obviously one shaft is going to be stronger than the other...and, the lighter shaft is around USD115, but the heavier shaft closer to USD150...same part#... ...epc-data usually tells a tale ~ the amayama listing for 39100-23U60 has a note "Longest side is between 60 and 105 cm" ; no such info is there for 39100-23U70 ...and given the great disparity in price between the 2 parts, it makes me at least curious (to the point of caution) where the 'extra money' went? ...ie; these 2 parts have a cost difference that (to myself at least) isn't explained by 'plastic boot'...ie; with amayama there's AUD700 price difference ...plastic versus rubber?...I'm not seeing it like that...and 60cm ~ 105cm...??...that's a huge disparity....something hinky going on here... I'd try searching by VIN, not model... /2cents
    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
×
×
  • Create New...