Jump to content
SAU Community

Recommended Posts

Hey guys

Im currently looking at a AU XR8 manual as a tow car for my 32 and for the misses to drive during the week.

I was just wondering if any one up there has owned one and had any problems?

Or if theres any comman faults i should be on the lookout for?

I test drove it today and for a car thats done 210,000kms i was pretty impressed with the feel of the engine and driveline.

Any input would be much appreciated.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/357250-au-xr8/
Share on other sites

They use lots of fuel....

You want one of these (at a really good price too...)

http://www.carsales.com.au/all-cars/dealer/details.aspx?R=9509282&__Qpb=true&Cr=1&__Ns=pCar_RankSort_Int32|1||pCar_PriceSort_Decimal|1||pCar_Make_String|0||pCar_Model_String|0&keywords=&__N=1216%201247%201252%201282%204294967079%20903%20408%204294966839&SearchAction=N&silo=1011&PriceTo=408&seot=1&__Nne=15&trecs=7&__sid=12CB54BF3AF7

Not bias or anything......

I LOVE BMWs! FWIW, my mum has a 528i E39 and I've managed 6.2L/100km out of it ;) ^V8 so good for towing I guess lol.

Edited by Ten Four
Link to comment
https://www.sau.com.au/forums/topic/357250-au-xr8/#findComment-5712267
Share on other sites

^ ^ ^ So long as that 535i has had all its services done properly, it's a bargain.

I'd check fault codes and fluid leaks re side tanks, water pump, oil. Electronic digital cluster can degrade over time.

Even as a V8, the beemer uses much less fuel than the XR8 and the E39 cornering ability is renowned

Link to comment
https://www.sau.com.au/forums/topic/357250-au-xr8/#findComment-5712511
Share on other sites

If you are going to use it for towing, get an auto.

Braked tow capacity for a manual is nearly half of what an auto is rated for.

And yes they are thirsty, it cost me $140 in fuel to go from Sydney with the trailer to Newcastle then back with the car on.

On average about $120 a week in fuel to run. We use premium though.

Link to comment
https://www.sau.com.au/forums/topic/357250-au-xr8/#findComment-5712547
Share on other sites

Mmmmm......yeah get a beemer, casue like, it'll be super cheap to fix when things start wearing out prematurely because you've been using it as a tow vehicle.

Hell, the extra $12 million dollars it will cost to maintain a beemer will be more than offset by the $15 per week saving in petrol you are bound to make.

Wait, I've just re-read you OP and realised you didn't ask for an alternative to an AU XR8. Silly me.

The AUs are bullet proof and pretty much perfect for what you want. Any vehicle capable of towing another vehicle frequently without collapsing in a heap is going to use a bit more juice than the rest as it's A) Heavier - to deal with the extra stress of towing and B) going to have a bigger motor.

As long as the AU has been looked after you shouldn't have any issues.

Link to comment
https://www.sau.com.au/forums/topic/357250-au-xr8/#findComment-5712581
Share on other sites

Mmmmm......yeah get a beemer, casue like, it'll be super cheap to fix when things start wearing out prematurely because you've been using it as a tow vehicle.

Hell, the extra $12 million dollars it will cost to maintain a beemer will be more than offset by the $15 per week saving in petrol you are bound to make.

Wait, I've just re-read you OP and realised you didn't ask for an alternative to an AU XR8. Silly me.

The AUs are bullet proof and pretty much perfect for what you want. Any vehicle capable of towing another vehicle frequently without collapsing in a heap is going to use a bit more juice than the rest as it's A) Heavier - to deal with the extra stress of towing and B) going to have a bigger motor.

As long as the AU has been looked after you shouldn't have any issues.

Lol. thumbsup.gifyes.gif

Link to comment
https://www.sau.com.au/forums/topic/357250-au-xr8/#findComment-5712663
Share on other sites

Mmmmm......yeah get a beemer, casue like, it'll be super cheap to fix when things start wearing out prematurely because you've been using it as a tow vehicle.

Hell, the extra $12 million dollars it will cost to maintain a beemer will be more than offset by the $15 per week saving in petrol you are bound to make.

Wait, I've just re-read you OP and realised you didn't ask for an alternative to an AU XR8. Silly me.

The AUs are bullet proof and pretty much perfect for what you want. Any vehicle capable of towing another vehicle frequently without collapsing in a heap is going to use a bit more juice than the rest as it's A) Heavier - to deal with the extra stress of towing and B) going to have a bigger motor.

As long as the AU has been looked after you shouldn't have any issues.

Win!

Link to comment
https://www.sau.com.au/forums/topic/357250-au-xr8/#findComment-5712716
Share on other sites

Which series is it? Is it a series 1 XR8? If you can, try to go for a later model with the 220KW engine.

The mechanicals of the AUs are pretty reliable, but the interior quality can degrade quite heavily over time. Also, some of the smaller things like the electriconics can be unreliable. I've known of several AU owners (including my dad) who had constant problems with the radio, electric windows and mirrors and some of the engine management electronics. But I guess any used car would have these problems.

Link to comment
https://www.sau.com.au/forums/topic/357250-au-xr8/#findComment-5713946
Share on other sites

My dad had similar issues to those on his au.

I was looking at them a while ago. The basic 5.0 L engine isn't much more powerful (13kW) or torquey (32Nm) than the xr6 at the time. And, worst of all, made at about the same rpm. It certainly felt pretty slow and heavy, despite extractors and twin 3" exhausts (well, felt and WAS slow and heavy). Getting out of the r34 and straight into it didn't help though.

(Source: http://www.trueblueford.com/AU_XR_Specifications.html )

When I was looking at them the problem that kept coming up was a whining diff, which needed some pin replaced, can't remember how much it was. Certainly wasn't cheap. I also found the pedals sticky and numb, not smooth like in almost every japanese car I've driven.

All that said though, it's a lot of car for the dough and the noise was fantastic!!! Also cheap to fix and your average mechanic is capable of working on it.

Link to comment
https://www.sau.com.au/forums/topic/357250-au-xr8/#findComment-5714149
Share on other sites

Bit of a tangent here, but on the question of what feels faster, a torquey, low revving V8 will often feel slower than a high revving turbo 6 as it makes power everywhere which means no "coming on boost" which can often give the false impression of speed.

My mate has an SII BA XR8 and it's almost neck and neck between it and my R33 GTST (mine is ever so fractionally faster in a straight line) however the R33 feels much faster. I remember the first time I took him for a spin in it his head nearly exploded as he thought it was so damn fast. Fact is, it's not much different to his car, and he flogs his thing everywhere. It's just his thing makes pwer from idle so lacks that kick in the pants feel that pretty much everyone on here is likely addicted to.

So while something like an XR8 may feel a lot slower than something like a turbo skyline, fact is there's probably a lot less between them than you think. And when it comes to corners, it's about 70% driver 30% car so a good steerer in an XR8 will likely spank a nubcake in a skyline.

Link to comment
https://www.sau.com.au/forums/topic/357250-au-xr8/#findComment-5714459
Share on other sites

I agree with the cowboy above, but I was also watching the speedo and there was a big difference between it and the r34 (running on 12-13 psi with exhaust, nothing too fancy). In terms of feel it felt slower than my current magna, but i don't think that was the case.

Also, unless I'm mistaken, the ba v8 was a crapload better than the au. The numbers on the au xr8 over the xr6 arent great for the au:

xr6

172 kW @ 5000 rpm

370 Nm @ 3500 rpm

xr8

185 kW @ 4600 rpm

412 Nm @ 3500 rpm

I'd go the xr6. Actually I would and did go magna. Not sure how it'd go towing a car though. There was a towcar thread on here a little while ago that in a nutshell strongly recommended people buy big 4wds so that the 2 tonnes of gear following can be kept under control.

Link to comment
https://www.sau.com.au/forums/topic/357250-au-xr8/#findComment-5714499
Share on other sites

I recall the time that the AU XR8's were running out, Ford were doing some interesting stuff with them. One of the car magazines put one on the dyno and it nearly made the flywheel ppower figure at the wheels. Apparently they were using roller rockers and other goodies in these engines to try and catch the 5.7 Holdens, even though the marketing department never made a lot of noise about it.

As others have said, they are pretty rugged, no nonsense cars that are generally good value for money. They'll never impress euro or jap import snobs, but you do get a fair bit of car for the money.

The unreliable electrics seems to be common in Falcons. Mine had to have the following replaced under warranty: ECU, Central locking computer, power mirrors and power door lock actuators (twice). Each time I took it in for a complaint, the response was "yeh, they all do that" >_<

Link to comment
https://www.sau.com.au/forums/topic/357250-au-xr8/#findComment-5714546
Share on other sites

Au Fords were actually very mechanically sound. You shouldn't have many problems with it, mechanically that is - It had the lowest warranty issues of all family sedans during it's time (even less than the Toyota Camry and unlike the VT, which had the highest warranty issues.)

Their manual gearbox is also unbreakable. Power-wise the au S1 and 2 left much to be desired. at ~175kw The s3 on the other hand was 220kw. Torque was awesome though so for towing you shouldn't have a problem.

If it's for a good price as you say, then go for it.

Link to comment
https://www.sau.com.au/forums/topic/357250-au-xr8/#findComment-5714614
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...