Jump to content
SAU Community

Recommended Posts

Hasn't accepted yet.... :( Frowny face

oy, i will add you :P

[email protected]

thought i was camera proof until i gunned it through an orange on the westlnk the other night and 'flash-flash' ...going to have to research those ghost plates, pretty sure it was the speed not the red light.

Link to comment
https://www.sau.com.au/forums/topic/358645-bang/page/4/#findComment-5734178
Share on other sites

  • Replies 68
  • Created
  • Last Reply

Top Posters In This Topic

Unless your speedo starts eating the gear drive, you don't need to calibrate them, this is why they have to be between 0 and 10% over read at any time for any configuration of tyre approved by the manufacturer.

Most cars over read by at least 3% on brand new tyres. Oh and new to worn out tyres will alter reading by approx 0.5%...

That doesn't help Import drivers or older cars.

Link to comment
https://www.sau.com.au/forums/topic/358645-bang/page/4/#findComment-5736920
Share on other sites

That doesn't help Import drivers or older cars.

Perhaps not, but if a speedo becomes more inaccurate over time shouldn't recalibration be part of routine maintainance? I guess it's much like adjusdting headlights, something very important that everyone overlooks as it isn't regulated.

At the end of the day, it's up to the road user to obey the rules. If you get caught breaking those rules and your only excuse is "lol, soz my speedo is out" it is very likely you will end up with a speeding fine AND a defect ;)

Link to comment
https://www.sau.com.au/forums/topic/358645-bang/page/4/#findComment-5736947
Share on other sites

SMH states that the ADRs specify a 10% margin for error either way, yet the actual ADRs say that the margin for error only applies that the car is always going equal to or less than the speed displayed on the speedo...

I wonder what else in that article is incorrect?

TL;DR - Sensationalist journalism

Because the ADR changed in 2006 - and ADRs aren't retrospective. So vehicles produced before 2006 happily comply with the old ADR and the new ADR does not apply to them.

The old pre-2006 ADR stated (loosely) +-10% accuracy at speeds above 40kph (I beleive), the new ADR changes that. However, how many cars are on the road that were build pre-2006? The new rules essentially disallow under-reading, and permit over-reading by up to 4kmh + 10% (there's a formula involved, I believe someone has already posted this).

The other thing to consider is all the other factors that will impact speedometer readings -

+ tyre wear

+ tyre pressure

+ vehicle load

And that ignores more human factors like many speedos only displaying increments of 5kph, or particularly sized/shaped speedometer needles.

Unfortunately, the politicians really don't give a damn - it's all about revenue raising, not facts or 'real world'.

Link to comment
https://www.sau.com.au/forums/topic/358645-bang/page/4/#findComment-5737147
Share on other sites

It'll be interesting see if as a consequence of <1km/hr tolerance, the stats of rear-enders goes up.

And they probably don't do a count of those anyway.

Rear-enders are probably already on the rise - not just from wet roads which has always been the case, but from texting.

Link to comment
https://www.sau.com.au/forums/topic/358645-bang/page/4/#findComment-5737202
Share on other sites

It'll be interesting see if as a consequence of <1km/hr tolerance, the stats of rear-enders goes up.

And they probably don't do a count of those anyway.

Rear-enders are probably already on the rise - not just from wet roads which has always been the case, but from texting.

Funny you mention this...

P Platers have the STRICTEST laws in regards to speeding on them... Yet they're the lowest cause of rear end accidents... So by that fact alone, it should technically reduce...

Link to comment
https://www.sau.com.au/forums/topic/358645-bang/page/4/#findComment-5737367
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
×
×
  • Create New...