Jump to content
SAU Community

Recommended Posts

Hasn't accepted yet.... :( Frowny face

oy, i will add you :P

[email protected]

thought i was camera proof until i gunned it through an orange on the westlnk the other night and 'flash-flash' ...going to have to research those ghost plates, pretty sure it was the speed not the red light.

Link to comment
https://www.sau.com.au/forums/topic/358645-bang/page/4/#findComment-5734178
Share on other sites

  • Replies 68
  • Created
  • Last Reply

Top Posters In This Topic

Unless your speedo starts eating the gear drive, you don't need to calibrate them, this is why they have to be between 0 and 10% over read at any time for any configuration of tyre approved by the manufacturer.

Most cars over read by at least 3% on brand new tyres. Oh and new to worn out tyres will alter reading by approx 0.5%...

That doesn't help Import drivers or older cars.

Link to comment
https://www.sau.com.au/forums/topic/358645-bang/page/4/#findComment-5736920
Share on other sites

That doesn't help Import drivers or older cars.

Perhaps not, but if a speedo becomes more inaccurate over time shouldn't recalibration be part of routine maintainance? I guess it's much like adjusdting headlights, something very important that everyone overlooks as it isn't regulated.

At the end of the day, it's up to the road user to obey the rules. If you get caught breaking those rules and your only excuse is "lol, soz my speedo is out" it is very likely you will end up with a speeding fine AND a defect ;)

Link to comment
https://www.sau.com.au/forums/topic/358645-bang/page/4/#findComment-5736947
Share on other sites

SMH states that the ADRs specify a 10% margin for error either way, yet the actual ADRs say that the margin for error only applies that the car is always going equal to or less than the speed displayed on the speedo...

I wonder what else in that article is incorrect?

TL;DR - Sensationalist journalism

Because the ADR changed in 2006 - and ADRs aren't retrospective. So vehicles produced before 2006 happily comply with the old ADR and the new ADR does not apply to them.

The old pre-2006 ADR stated (loosely) +-10% accuracy at speeds above 40kph (I beleive), the new ADR changes that. However, how many cars are on the road that were build pre-2006? The new rules essentially disallow under-reading, and permit over-reading by up to 4kmh + 10% (there's a formula involved, I believe someone has already posted this).

The other thing to consider is all the other factors that will impact speedometer readings -

+ tyre wear

+ tyre pressure

+ vehicle load

And that ignores more human factors like many speedos only displaying increments of 5kph, or particularly sized/shaped speedometer needles.

Unfortunately, the politicians really don't give a damn - it's all about revenue raising, not facts or 'real world'.

Link to comment
https://www.sau.com.au/forums/topic/358645-bang/page/4/#findComment-5737147
Share on other sites

It'll be interesting see if as a consequence of <1km/hr tolerance, the stats of rear-enders goes up.

And they probably don't do a count of those anyway.

Rear-enders are probably already on the rise - not just from wet roads which has always been the case, but from texting.

Link to comment
https://www.sau.com.au/forums/topic/358645-bang/page/4/#findComment-5737202
Share on other sites

It'll be interesting see if as a consequence of <1km/hr tolerance, the stats of rear-enders goes up.

And they probably don't do a count of those anyway.

Rear-enders are probably already on the rise - not just from wet roads which has always been the case, but from texting.

Funny you mention this...

P Platers have the STRICTEST laws in regards to speeding on them... Yet they're the lowest cause of rear end accidents... So by that fact alone, it should technically reduce...

Link to comment
https://www.sau.com.au/forums/topic/358645-bang/page/4/#findComment-5737367
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I think in the modern era we live in, if I were converting a hydro lifter head to solid, particularly when chasing revs, I'd be seeing what I could do to use shimless buckets. Those of us with Neos usually have this persistent niggling fear of a shim getting spat out and ruining everything. Shim-over is...yucky that way. At least the Tomei kit appears to be conventional, but it would still be nice if they'd decided to go shimless.
    • Ok guys thank you very much. GCG highflow it is then 🙂 
    • forgot to mention that when it does this it does not kill the engine, but I have not kept the pedal down long enough to let it, as I see no reason to beat up on it as its got to be something simple, small and dumb causing this.  And as soon as I let off pedal, the engine returns to its normal super smooth operation and rpms re-stabilize quickly, once below 4k. 
    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
×
×
  • Create New...