Jump to content
SAU Community

Recommended Posts

Hi guys, just looking to get a bit of advice on what state to leave my fuel tank level in.

Basically, i have my GTST as a weekend only car which means it gets driven 2-3 times over a weekend and then just sits all week.

In doing this i have basically been filling it up with enough fuel on friday to last me the weekend then leaving it empty for the week before again filling enough fuel for use on that weekend.

My rationale for this is that I know fuel can go off after a period of time reducing the octane level etc. My car is tuned quite hard and iv been instructed to only ever put BP98 in it from a reputable shop. As such i do this and only with enough fuel for that weekend's driving so i always have fresh fuel in it. If i was to fill it up completely a tank would probably last me 1-3 months and im worried that fuel in the tank for up to 3 months would be gettting shitty and perhaps causing problems (pinging etc from the fuel losing octane level).

Do people agree with this rationale or is there an alternative reason to actually be keeping the tank full? (or fuller)?. Im wondering if always having less than 20% in the tank and usually it is sitting there with <5% in the tank will be encouraging corrosion in the tank or some other problem i havent considered...?

Link to comment
https://www.sau.com.au/forums/topic/359337-should-i-leave-fuel-in-the-tank/
Share on other sites

as i mentioned above though- it would be up to 3 months that a full tank of juice would take to be used in my car. I know it wouldnt go off in 2 weeks.

also i doubt you would notice a drop off in performance even if the fuel was starting to go off. There would probably just be increased ping that you wouldnt be able to notice but would not be good on your motor. Hence my predicament...

just keep doing what you're doing, it's fine.

The only bad thing about not having a full tank is the slight risk of fuel surge when you're going hard around corners and stuff. But skylines don't get it that bad anyway, not like WRXs which'll surge if you're under 1\3 and think about going around a corner.

Went to an SAU trackday at wakie last july, last lap and the fuel light came on, loaded it on the trailer and have driven it around the block once since then.. going to chuck 10ltrs in this weekend with some octane booster i think!!

mmm, i might keep that in mind as i down have some 'favourite corners' that have me at pretty high cornering g's for perhaps 8-10secs so perhaps not the best thing if the tank is very low or even empty (fuel light on)...

does anybody know if it is one side or the other that the pump draws from? therefore will be more likely to suck air under cornering 1 way or the other...

Edited by jjman

there is no problem filling the tank and running the fuel for 1-3 months. also at say the 2 month point when it's a qtr full just top it up again. the fuel tank should have a check valve so it can breath out. the advantage of filling the tank is less air in the tank. being that the tank is under the car, and in a cool dark place with no UV or exposure to air it should last quite a long time. certainly 3 months would be no problem.

the other problem with running the tank low is it concentrates all the dirt/silt etc that is in the tank into such a small quantity of fuel and can cause contamination.

mm, food for thought on the contrary arguement. Might go for keeping it at at least over a 1/4 tank for the driving phase n also making sure i dont leave it too empty in the weekly garage time.

cheers again peeps :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...