Jump to content
SAU Community

Recommended Posts

Ok i have used fishing wire to debadge the stagea. I has tried to use grease and wax remover to get rid of the glue but still leaves the outline of the wording. What have you used in the past thatwill get rid of the glue and any marking from the lettering.

Link to comment
https://www.sau.com.au/forums/topic/359557-debaging/
Share on other sites

You could also try Mineral Turpentine on a rag and/or a very light polish as there will be a difference in the paintwork finish now where the badges have been...

+1 thats what i did.. just polished it up and it came up perfecto

Link to comment
https://www.sau.com.au/forums/topic/359557-debaging/#findComment-5742633
Share on other sites

Ive done the same on mine got all the adhesive of with some metho on a rag and then clay bar, cut and polished then waxed where the badge was but you can still see where it was...... Think i need to find someone to hit it with the buffer.

Link to comment
https://www.sau.com.au/forums/topic/359557-debaging/#findComment-5742798
Share on other sites

It should be fine, although it will most likely strip the polish from the surface leaving you with a dull patch that you'll need to repolish.

It's not different from a bit of petrol running down the side of the car when you're filling the tank - I hate it when it does that!

Link to comment
https://www.sau.com.au/forums/topic/359557-debaging/#findComment-5743078
Share on other sites

Ok got all the glue off. Not I just have like a dirty outline of what used to be there. What would be the best grit sandpaper to remove this before I cut and polish. Would wet sanding be best

Just use a cutting compound, and keep going until you get the finish you're after. The clear coat on these is far too thin for wet sanding IMO.

Link to comment
https://www.sau.com.au/forums/topic/359557-debaging/#findComment-5743249
Share on other sites

Just use a cutting compound, and keep going until you get the finish you're after. The clear coat on these is far too thin for wet sanding IMO.

+1 on the cutting compound and i wouldn't go near it with wet & dry either.

I'd also use a light hand when using the cutting compound and just take your time.

Link to comment
https://www.sau.com.au/forums/topic/359557-debaging/#findComment-5743266
Share on other sites

unfortunately the badge the car in the factory when the paint hasnt quite cured so leaves marks. plus the weather etc doesnt help.

mine and craigs are the same. no amount of cutting and polishing etc got the marks out of mine

Link to comment
https://www.sau.com.au/forums/topic/359557-debaging/#findComment-5743627
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...