Jump to content
SAU Community

Recommended Posts

Bout 1900 dollars P.A. with just car and full excess, though im only 21 and living in sydney. for a R32 GTR insured for 20k

either way because you live in sydney its goin to cost a damn fortune, my car use to be insured in queensland and it was around the 1300 mark

yeah i was doin pay by the month and it was around $110, i think i get a tiny discount cause ive been with them since i was 17 and have a no claims or loss of lisence

NSW has the highest insurance rates in Australia, especially sydney with its awsome crime rates and thefts

, QLD and VIC being some of the cheapest

  • 2 weeks later...

easy answer dude, crime rate and car theft.... so many dodgy wreckers in sydney as well.

some if given the chance will pick up a car with a forklift if it has been sitting on the street in their area for more then a day.

Freakin Game mofo's!!!!!!!

just car $2000 pa, normal excess $1500, i'm 31yo in vic. i have informed then of all mods done and even proved that all parts are genuine nismo, so my payout amount is higher than what redbook says.

2000 Nissan Skyline GT-R V-Spec R34 Previous Valuation Prices * Private Price Guide$35,800 - $40,600 * Trade In Price Guide$29,500 - $34,300 * Average Km110,000 - 200,000

Honestly i don't how redbook calculate there evaluations.

Edited by GD2ILA
  • 1 year later...

Hey guys, 27 male, got quoted 3000 by just car. Is that right? clean record, 01 R34 GTR.

Im looking at everyone elses and its so much cheaper? Will all the P.A ones, did you raise your excess cost? I want mine to be the standard but if I have to raise it then i will.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...