Jump to content
SAU Community

Recommended Posts

  • Replies 85
  • Created
  • Last Reply

Top Posters In This Topic

the black nismo alloy knob rocks... and the heat doesnt bother me either... but one with a red glowing H diagram would be neat...

Yeah, would be awesome if they can do it in aluminium with H pattern :D:D:D

still keen :thumbsup:

Please put one for me as well. Let me know when you buying

To easy guys. I'll PM you when I open the group buy. Might do it tonight or tomorrow.

i'm interested.. but how will it fit againt the skyline gear stick? this picture looks like the gear stick is lower down? will the boot marry up to the skyline?

dont they have to do more than just make it 10mm to fit the skyline?

ie. shape of the base surround, height of the stick, etc?

Other than the diameter the only factor is the length of the internal thread in these new gear knobs. If there is plenty of thread it will bottom out on the stick and won't be a problem. If the length is short, it may not go all the way down and sit a little bit higher. This really depends on how tall the gear stick is that you had on there before.

In regards to the gear boot. I suppose it depends how much play there is in the boot. Mine is custom made and is a bit baggy so should be allright in that respect. In regards to the base of the boot once again varies from boot to boot in how it is stitched.

However I want to replace mine with suede and I have found a manufacturer in the UK that does good ones for good prices. So we can always get custom made ones to our specifications.

Please let me know if I am over looking something.

Phil, not sure if you have mentioned this or not, but do they only make it in leather?

I want aluminium xD

The ones I posted on the first page are the ones they make. All have leather.

Basically the options are as follows (I will go into more detail in the actual group buy):

-All leather

-Leather with a ring of chrome

-Leather with a ring of aluminium

-Leather and chrome mix

-Leather and aluminium mix

Ah yes handbrake boots! Forgot about them. Definetely keen on that aswell since mine is the factory one and looks a bit old now.

Wouldn't mind actually doing something about the handbrake itself. Havn't really seen any one doing anything on a Skyline though.

my little bro has the nismo alloy one in a black 32. gets real hot in summer, but is easily fixed by removing it from the car and running it under cold water for a minute or 2...or until it stops steaming :happy:...seriously tho. it gets real hot, even under a sock

I would be keen, any idea on how they will sit ? Ive got a small "ball" shaped one and I love it, I bought another one of eBay and it was a stick type one and it sat up way to high, to the point were I was literally punching my stereo when changing to 3rd.

Just do what I done when I accidentily bought a m12 nismo knob, get a 10mm bolt, put it at the end of a screw so you have room to work with it, then using a bench grinder grind the edges till it's perfectly round and fits the m12 hole in the gear knob, then just epoxy it into the knob, whole process should take about 30 mins :)

Also just so you know why I havn't posted the group buy up yet.

I'm just trying to confirm with them whether the gear knobs actually have a thread inside them or whether they are just a hollow shaft. Because I believe a lot of European cars don't have a thread on the end of the shifter, they are just a shaft.

EDIT: Here is an install I found. See how there is no thread.

http://www.seat-leon.de/vboard/showthread.php?t=70056

The group buy will be for the gear knob only from this supplier.

There is another guy in the UK that does really good quality gear boots which we could also do a group buy for. However that isn't in the plans at the moment.

I'm just trying to confirm with them whether the gear knobs actually have a thread inside them or whether they are just a hollow shaft. Because I believe a lot of European cars don't have a thread on the end of the shifter, they are just a shaft.

I know when my mate changed his gear knob on his E46, it wasn't threaded inside the knob. Just had to pop off the old one and slide the new one on.

So they do or don't have a thread in them?

That's what I'm trying to find out.

I emailed them so waiting for a response.

If not, as Craig said, we could just hand tap them since i'm assuming the inside would be aluminium so should be soft enough to tap.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...