Jump to content
SAU Community

Recommended Posts

Get a replacement or better after market fuel filter

Locate fuel filter (I don't have an R32, but I think it is in the back under the trunk?)

Unplug fuel pump fuse

Start car, let die :O

Try to start car again to be sure there is no left over pressure in fuel line

Pull out old fuel filter

Enjoy getting high from fuel

Put in new fuel filter

Return fuel pump fuse

Start car, let idle :cool:

Done

Link to comment
https://www.sau.com.au/forums/topic/360983-fuel-filter/#findComment-5762879
Share on other sites

  • 8 months later...

Sorry to dig up this old thread but didn't think it worthwhile starting a new one with the same topic.

Would someone be able to tell what size fuel hose to buy, I'm about to change my filter and want some spare fuel line on hand in case the original stuff is damaged when I remove the old one, probaly a good idea to have a couple of new clamps too.

Regards

Mike.

Link to comment
https://www.sau.com.au/forums/topic/360983-fuel-filter/#findComment-6159070
Share on other sites

Got the filter from Nissan Coopers Plains for $33 though they tried to charge me $39 apparently the price changes from when you ring for availability to when drive there to get it.

Also the Repco man tried to talk me into $28 per meter high pressure line, though I walked out with the standard 5/16th, stuff for $6.

Mike.

Link to comment
https://www.sau.com.au/forums/topic/360983-fuel-filter/#findComment-6160903
Share on other sites

but you do need the high pressure EFI fuel line dont you???

I know thats what I use...

To be honest I don't know, but the line I had to cut off looked to be original and of the same spec as the cheaper line I bought. Would be good if someone in the know can confirm.

Link to comment
https://www.sau.com.au/forums/topic/360983-fuel-filter/#findComment-6161220
Share on other sites

Id get EFI line. Peace of mind is better then saving a few dollars

Very true, I did a little research on the line I bought and it seems to have a working pressure of 50 psi, might try and source some 150 psi stuff. I don't want to start any fires in my engine bay, or anywhere else for that matter.

Mike.

Edited by Missileman
Link to comment
https://www.sau.com.au/forums/topic/360983-fuel-filter/#findComment-6161277
Share on other sites

That line you got is used mainly for carby engines, it can blow out/split if used on EFI applications. Also, you can use a z200 fuel filter, its alot cheaper than the one earlier posts have gotten

Link to comment
https://www.sau.com.au/forums/topic/360983-fuel-filter/#findComment-6161321
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Kittens in first to claim dominance of the residence, then puppies later From past experience, the other way around can be problematic to say the least  Those weird "Dobby looking"  little kittens are not cheap....LOL
    • At least yours have parkour down pat. One of mine will still trip over his own shadow and fall over... He's a special type of cat... Ha ha ha
    • The question then becomes - was there any fluid coming from that hole before you did the rebuild ?    You may not have noticed, of course.   Depending on how you did the rebuild, the possibility has to be considered that somehow (cleaning ?)  fluid entered that hole and is now being 'forced'  out by small movements of the proportioning valve.   From the factory, there's actually a small rubber plug in that hole but with age and under-bonnet heat it's quite common for it to 'go missing'.  That rubber plug is designed to allow the venting process but also to prevent 'stuff' getting to the area (prevent corrosion, etc).   The plug is also not available as a spare part AFAIA. Personally I wouldn't race and buy a new master just yet but keep an eye on the area to see if the 'leak' continues.   If you're concerned about brake fluid damaging nearby paintwork, cable tie a piece of suitable absorbant material over the hole and remove/monitor occasionally.    Operation of the proportioning valve and the brake master itself won't be affected, but also keep an eye on brake fluid level, of course. In terms of a new master, the genuine part is getting expensive, unfortunately.  Amayama is showing AUD900+.   I was searching recently and there's an aftermarket part available from Japan made by 'Parts Assist': https://zenmarket.jp/en/yahoo.aspx?q=BNR32%2bBM50&p=1 Whether it's any good I have no idea, although in my experience Japanese aftermarket stuff is pretty good quality-wise.   The above site allows overseas buyers to purchase stuff more easily from Japan but there are fees and shipping costs, of course.   The original Japanese seller page is here: https://auctions.yahoo.co.jp/jp/auction/p1197401228 Copper/Nickel is fine but I still prefer bundy tube and it's also cheaper.
    • Your chihuahuas look weird!
×
×
  • Create New...