Jump to content
SAU Community

Recommended Posts

Just had compression test done

Results came back rubbish

Between 111-114 across all six.

Mechanic said he is going to use another dial just to be certain, as the wear is very even.

f**king disappointing,

Question :

Wouldnt rubbish figures like that be showing serious deteriorating performance signs??? I had this done out of curiosity as i was just about to upgrade turbo. Still performs like it always has. Really well. Has a 125k on the clock

Link to comment
https://www.sau.com.au/forums/topic/360991-compression-results/
Share on other sites

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

1. They are consistent - this is good, not rubbish

2. It could have been done slightly wrong - meaning there is no actual issue

Given consistent results across all 6 it's either one of two things.

The motor is a little bit tired or the test was perhaps not dont quite correctly.

Have it retested perhaps by another workshop just to see what happens. With legit km's you'd probably expect closer to 130-140 but personally i wouldnt get too excited just yet until it gets retested.

If it comes back and does show that it is similarly low then ye the motor is a bit tired and perhaps not a good idea to ask too much of it. 250rwkw on a safe tune would be about sensible limit IMO.

1. They are consistent - this is good, not rubbish

2. It could have been done slightly wrong - meaning there is no actual issue

Given consistent results across all 6 it's either one of two things.

The motor is a little bit tired or the test was perhaps not dont quite correctly.

Have it retested perhaps by another workshop just to see what happens. With legit km's you'd probably expect closer to 130-140 but personally i wouldnt get too excited just yet until it gets retested.

If it comes back and does show that it is similarly low then ye the motor is a bit tired and perhaps not a good idea to ask too much of it. 250rwkw on a safe tune would be about sensible limit IMO.

Good to hear i guess.

Was only aiming for 250rwkw give or take and decent response.

Its being retested with another dial. If its still the same, taking it elsewhere for one last crack regardless.

Cheers for your response.

I get it changed every 5 thousand. Its not burning oil or blowing excessive smoke. Doesnt go through coolant either

Does however not seem to peak as much boost. Originally tuned for around 13psi. Now under load (and even on the cooler nights recently) only seems to reach just on 11psi.

Occasionally the idle drops off slightly from around 700 to 500 revs and has stalled once or twice coming to a real quick stop at the lights.

Ive never had the 02 replaced.

Edited by Mattw_83

I wouldnt worry about it it to much considering the numbers are very very even, as someone else said, put a couple drops of oil in through the plug hole and do the test again and also do a leak down test and it'll tell the story a bit better, i'd say its just old age and or probaly had a headgasket changed to a thicker item before you bought the car

Slap your new turbo on and screw the boost into is what i'd be doing.

Big thing i find with comp test results is from gauge to gauge it varys but as long as the numbers are with in 5% of each other she's still good!

Edited by 32rrr

The engine sounds like its a little tired. Is the motor breathing @ all, check your intercooler piping for oil if you still run a standard breather setup.

Apologies for the ignorance mate, what do you mean by breathing?

Start car, better with a mate, so he can blip the throttle.

Take your oil filler cap off and see if it is breathing heaps = indicates blowby = rings/liners worn. Keep a rag handy,so you can half cover the hole just in case it starts to spit oil.

Do it with a couple of cars if you can so you can see the difference.

Start car, better with a mate, so he can blip the throttle.

Take your oil filler cap off and see if it is breathing heaps = indicates blowby = rings/liners worn. Keep a rag handy,so you can half cover the hole just in case it starts to spit oil.

Do it with a couple of cars if you can so you can see the difference.

you can blip the throttle by pulling the cable with your hand lol....last time I took the filler cap off and did it, the cams flicked oil all over my face bahahaha

Just had compression test done

Results came back rubbish

Between 111-114 across all six.

Mechanic said he is going to use another dial just to be certain, as the wear is very even.

f**king disappointing,

Question :

Wouldnt rubbish figures like that be showing serious deteriorating performance signs??? I had this done out of curiosity as i was just about to upgrade turbo. Still performs like it always has. Really well. Has a 125k on the clock

hey mate,

for your interest i just did an engine swap but tested my rb20 (cold test) which has 339000km on it, i got between 120-127 on mine

mick

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...