Jump to content
SAU Community

Recommended Posts

From my experience you will need to run bigger injectors then 700's to make 400kw+. When I was making 374 RWKW I ran 700cc Sards with a duty cycle of up to about 96. At the advice of my tuner (a reputable one)I upgraded to Sard 800's to allow for more headroom. This allowed me to run a bit more boost and make 390 RWKW. Now the dc gets to about 85. This is with a -5 2.7 setup. I wonder why the difference between my experience and some others in this thread? Is it just a difference in dyno readings? I know of others with similar results to mine.

Tim.

i know that extra capacity chews up DC due to the additional torque & your setup is a 2.7ltr as well

my old 3ltr had 1600's & dc was above 60% & that was making 405awkw

From my experience you will need to run bigger injectors then 700's to make 400kw+. When I was making 374 RWKW I ran 700cc Sards with a duty cycle of up to about 96. At the advice of my tuner (a reputable one)I upgraded to Sard 800's to allow for more headroom. This allowed me to run a bit more boost and make 390 RWKW. Now the dc gets to about 85. This is with a -5 2.7 setup. I wonder why the difference between my experience and some others in this thread? Is it just a difference in dyno readings? I know of others with similar results to mine.

Tim.

Wow now that is a very different results indeed mate.

I don't think an extra 50cc is going to make a 30% duty difference from a 2.65 to a 2.7

3ltr would of course but very interesting indeed.

As i said earlier best i can get under full load in 4th is 64%

Suck it an see Marko!!

ash, the displacement of a gtr engine is 2568cc hence a deficit of just under 150cc.

I'm leaving the 700's in there and see what happens when dyno tuned

Rebuild with larger pistons etc? :)

Wow now that is a very different results indeed mate.

I don't think an extra 50cc is going to make a 30% duty difference from a 2.65 to a 2.7

3ltr would of course but very interesting indeed.

As i said earlier best i can get under full load in 4th is 64%

Suck it an see Marko!!

Really need to know where the power is made. If he makes 400kw at 9000 rpm his going need more injector than a car that makes 400kw at 7000 and falls away to 380 by 8000...

Is that pull done in 3rd gear? What is your rev limit set to? Afrs look good no unnessarry fuel used there.. I'm on sard 800's aswell made 450awkw rev limit 8600 power just starting to nose over at 8.4 on 98/toluene mix. My Afrs are a bit rich at 11.0 though. Engine efficiency would play role aswell..

Is that pull done in 3rd gear? What is your rev limit set to? Afrs look good no unnessarry fuel used there.. I'm on sard 800's aswell made 450awkw rev limit 8600 power just starting to nose over at 8.4 on 98/toluene mix. My Afrs are a bit rich at 11.0 though. Engine efficiency would play role aswell..

Dyno pull done in 4th. Rev limit set at 8300. Very rarely need to rev over 6500 though to drive it quickly.

I dont have another picture of the graph just now but you can just see that the afr settles dead on 12.

Tim.

  • 2 weeks later...
  • 3 years later...

I cannot find exactly what I was looking for in this thread, could have missed it?

What size injectors are needed for an RB30/26, Nitto 3.2Lt stroker to use 98 & E85 , building for response ?

Have to find out what is in it before I get worried about it, it had a lot of mods before I bought it and ready for some high HP if the previous owner wanted to turn up the wick.

I am sure the builder will not have their results suffer because of the wrong injectors after doing this type of build, would not look good :/

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...