Jump to content
SAU Community

R33 Nismo Lcd Screen Wiring Help

GTS11

By GTS11,
in Exterior & Interior Styling

 Share

Recommended Posts

GTS11 Apprentice

GTS11

Posted
Posted

Hi Guys,

Please forgive me if i have done this wrong, never posted before.

I have reciently bought a 33 with a nismo lcd dash (not connected to anything) and was wondering if someone can help me out. At the back there is a RCA plug and 2 pins under it, im guessing there for power. Does anyone know which is positive & negitive?

any help would be greatly apreciated!

post-78369-0-54976600-1303749737_thumb.jpg

post-78369-0-53963300-1303749765_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/362118-r33-nismo-lcd-screen-wiring-help/
Share on other sites
GTS11 Apprentice

GTS11

Posted
  • Author
Posted

yeah there is the ej1 and other systems,

I have a deck that plays dvd's and i was going to plug that in through the rca lead to test if the lcd screen works but i think the two pins below are for power and was just wondering if anyone knew which was neg and pos?

Skysthelimit Contributor

Skysthelimit

Posted
Posted (edited)

just to confirm for you, yes those pins are the power to the screen.

I have one of these in my car hooked up to the ej1 unit. But unfortunately off the top of my head I do not recall which of the pins is positive and negative, as mine was all ready to go with a power cable still fitted over them :P

Edited by Skysthelimit
  • 4 weeks later...
bngbng Enthusiast

bngbng

Posted
Posted

Hi i bought one of these nismo lcd cluster, but it only came with the navigation system..does the navigation work in australia and have english? also i have a motec ecu..if i cant find a epson ej1 system am i best off with the HKS CAMP or HKS CAMP2 ? please help if can

thanks

DJSimmo Community Regular

DJSimmo

Posted
Posted

Hi i bought one of these nismo lcd cluster, but it only came with the navigation system..does the navigation work in australia and have english? also i have a motec ecu..if i cant find a epson ej1 system am i best off with the HKS CAMP or HKS CAMP2 ? please help if can

thanks

i had an EJ1 its broken the display chip is faulty and the display is scrambled.

Best bet is to get the HKS Camp 2 and the Nissan Consult harness it works really well and has allot more features compared to the EJ1.

You can also buy optional sensors for the HKS Camp 2 like boost, oil pressure, exhaust temp, oil temp etc

bngbng Enthusiast

bngbng

Posted
Posted

hey ok cool thanks for the help..ill look into the camp2

i had an EJ1 its broken the display chip is faulty and the display is scrambled.

Best bet is to get the HKS Camp 2 and the Nissan Consult harness it works really well and has allot more features compared to the EJ1.

You can also buy optional sensors for the HKS Camp 2 like boost, oil pressure, exhaust temp, oil temp etc

DJSimmo Community Regular

DJSimmo

Posted
Posted

hey ive been reading throu some other post about the hks camp2..will it connect to a aftermarket ecu ?

There is a possability the HKS Camp 2 might work with an aftermarket ecu because HKS offer a CAMP 2 Universal Adaptor which has to be hard wired or soldered onto the ecu wires.

Apparently the Universal Adaptor can pick up the following...

SPEED, RPM, INJECTOR, and THROTTLE

Check out the HKS CAMP 2 FAQ's

http://www.hksusa.com/faq/?ID=3516

bngbng Enthusiast

bngbng

Posted
Posted

ok thanks again for the help will look into it more thanks

There is a possability the HKS Camp 2 might work with an aftermarket ecu because HKS offer a CAMP 2 Universal Adaptor which has to be hard wired or soldered onto the ecu wires.

Apparently the Universal Adaptor can pick up the following...

SPEED, RPM, INJECTOR, and THROTTLE

Check out the HKS CAMP 2 FAQ's

http://www.hksusa.com/faq/?ID=3516

  • 3 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...