Jump to content
SAU Community

Recommended Posts

My apologies in advance if this topic has been covered before, just requesting some recommendations or if anyone can refer me to someone (mobile based) who offers their services to perform Paintless dent removals on vehicles, during business hours. I work in the Inner west area, in Sydney.

If you are able to provide me with assistance please leave a reply in this thread or via PM, thanks.

Link to comment
https://www.sau.com.au/forums/topic/362740-paintless-dent-removals/
Share on other sites

Hau works magic with his tools, hands, eyes and experience.

0433.248.666

He also does work for JapLink at Haberfield & his charges are very reasonable indeed.

Keep in mind that side panels, bonnet and boot are less time consuming than the roof.

  • 4 months later...

Hau works magic with his tools, hands, eyes and experience.

0433.248.666

He also does work for JapLink at Haberfield & his charges are very reasonable indeed.

Keep in mind that side panels, bonnet and boot are less time consuming than the roof.

I'm pretty sure he's the same guy I had hail damaged removed from yonks ago. Did a really good job. Not bad for the price too. More dents the cheaper it usually gets. lol.

^ ^ ^ Dave's right!

Aluminium if dented again in the same area, doesn't seem to allow the molecules to line up in the same fashion again + over time, aluminium becomes less malleable and more brittle.

That's why golf club manufacturers gave up on aluminium shafts.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...