Jump to content
SAU Community

Recommended Posts

Hey guys heres my build plan would this be adequate just for using as a street car:

RIPS RB30 Stock internal bottom ends, with RIPS modifications, fully refreshed

Standard R33 RB25DET VCT head *is there any modifications needed or just bolt on?*

R33 GTST PFC with boost controller kit

Yellow Jacket ignition coils

Walbro 255l Fuel pump

GTR intake plenum with 700cc injectors

HKS 3037 Pro S turbo *should i go bigger to a GT35R?*

Items in consideration:

Nitto Oil pump

Enlarged Sump

Cheers

Chi

Link to comment
https://www.sau.com.au/forums/topic/363243-rb30-build/
Share on other sites

Sounds 'adequate' to me for a street car haha.

There is heaps of info in the stickies above on what mods are required to get the twin cam head onto the rb30 bottom end.

Only comment I will make is that if you choose the 3037 then make sure you get the larger 0.87 housing if possible. I would recommend either a kando T67 or a 3076 with 0.82 housing. For a street car I would leave the GT35R alone.

You might as well go larger injectors to give yourself more headroom and if you ever decide to run E85. I would go ID1000's. Not sure whether that fuel pump will be enough.

Will you be using standard exhaust manifolds?

Link to comment
https://www.sau.com.au/forums/topic/363243-rb30-build/#findComment-5796770
Share on other sites

Standard R33 RB25DET VCT head *is there any modifications needed or just bolt on?*

HKS 3037 Pro S turbo *should i go bigger to a GT35R?*

The head bolts on but you can weld up/ block the VVT oil feed and shape the water gallery next to it and shape it to suit the rb30 water jacket. If you dont then there is approx 1mm of sealing area around that water jacket.

Go the 35R, the difference in price is nothing for the extra increase in power, you will be wanting more when u max out the 3037

Link to comment
https://www.sau.com.au/forums/topic/363243-rb30-build/#findComment-5796955
Share on other sites

the 26 plenum i have a blitz adaptor plate kit for it to be bolted on mmmm I think the RIPS 30 block has all the modifications so the head is to be bolted on without having to block the VCT oil feed etc ill email RIPS about this, exhaust manifold wise if i get a GT35R i will be going a 6boost manifold. but is the nitto oil pump needed?

Link to comment
https://www.sau.com.au/forums/topic/363243-rb30-build/#findComment-5796982
Share on other sites

the 26 plenum i have a blitz adaptor plate kit for it to be bolted on mmmm I think the RIPS 30 block has all the modifications so the head is to be bolted on without having to block the VCT oil feed etc ill email RIPS about this, exhaust manifold wise if i get a GT35R i will be going a 6boost manifold. but is the nitto oil pump needed?

iirc it has an external feed set up. theres no way of doing it without blocking the original feed, as it overlaps with a water gallery on the 30 block. the other way thats on here is to feed vct oil from the cam buckets by drilling out a brass fitting in the head

Link to comment
https://www.sau.com.au/forums/topic/363243-rb30-build/#findComment-5797002
Share on other sites

Go the 35R, the difference in price is nothing for the extra increase in power, you will be wanting more when u max out the 3037

I disagree, there is car on here (Al's) with an RB2530, he runs a GT3076 0.82 and makes 330rwkw with unbelievable response.

My argument is that I would prefer a super responsive ~330rwkw setup then a less responsive ~370rwkw setup for the street. It depends on the driver too on what they prefer.

I have just changed from a 280rwkw setup on an RB25 with less reponse and changed to 250rwkw with amazing response and it would beat the previous setup in all times but a rolling start from 80+ km/h

Link to comment
https://www.sau.com.au/forums/topic/363243-rb30-build/#findComment-5797416
Share on other sites

I disagree, there is car on here (Al's) with an RB2530, he runs a GT3076 0.82 and makes 330rwkw with unbelievable response.

My argument is that I would prefer a super responsive ~330rwkw setup then a less responsive ~370rwkw setup for the street. It depends on the driver too on what they prefer.

I have just changed from a 280rwkw setup on an RB25 with less reponse and changed to 250rwkw with amazing response and it would beat the previous setup in all times but a rolling start from 80+ km/h

At 378rwkw I have no lag with a GT35R .82

Edited by Alf
Link to comment
https://www.sau.com.au/forums/topic/363243-rb30-build/#findComment-5797916
Share on other sites

Wow you just created the first turbocharged vehicle to not have lag!!!

I think you mean the lag you have is acceptable for you. Put the car in 5th gear at 60km/h and tell me you have no lag.

Im almost there with that feat! :D

Link to comment
https://www.sau.com.au/forums/topic/363243-rb30-build/#findComment-5797985
Share on other sites

lol. ahhh it would appear I did...:whistling:

But to get back on point, the most responsive our race car ever was, was when it had a gt30 on it. Exact build spec was standard head and valves with tomei stage 1 cams retaining the vct, 6boost manifold with gt30 with .82 rear, 8.2:1CR and we were making 320rwkws. Then when we put a water methanol setup on it it bumped upto about 360rwkws and it was amazing! Pulled like a steam train but used to die off abit early up high.

Link to comment
https://www.sau.com.au/forums/topic/363243-rb30-build/#findComment-5799441
Share on other sites

lol. ahhh it would appear I did...:whistling:

But to get back on point, the most responsive our race car ever was, was when it had a gt30 on it. Exact build spec was standard head and valves with tomei stage 1 cams retaining the vct, 6boost manifold with gt30 with .82 rear, 8.2:1CR and we were making 320rwkws. Then when we put a water methanol setup on it it bumped upto about 360rwkws and it was amazing! Pulled like a steam train but used to die off abit early up high.

Exactly, what speed did it die off up high? I am tipping way above legal road speeds. Why such low compression??

Link to comment
https://www.sau.com.au/forums/topic/363243-rb30-build/#findComment-5800060
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...