Jump to content
SAU Community

Recommended Posts

I did a 10.02 @ 143 last time out but that was with only 450wkws that has now risen to 650wkws.A mid 9 is expected but we all know about expectations,Lol.I just wanna get out there with some Skylines rather than the usual v8s or rotors.

Mmm ok yeah that's not going to work haha!

Shame though, there's a few 500+awkw GTR's that want to come but they'll run too fast.

Really sorry we cant help you out - maybe come watch and just hang out with some non V8/Rotor guys at WSID for a change lol

  • Replies 436
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Dam I went to one of these days before I brought my GTR and watched TWOOGLE & 2RISMO both ducking into the 10's yet weren't booted? I've been looking forward to running at such an event ever since yet sadly not paying $200 for 1 run :verymad:

Mmm ok yeah that's not going to work haha!

Shame though, there's a few 500+awkw GTR's that want to come but they'll run too fast.

Really sorry we cant help you out - maybe come watch and just hang out with some non V8/Rotor guys at WSID for a change lol

There are ways around this... you could break the beam (and start the timers) then take off and see what MPH you can get. This can indicate your potential ET on a perfect run. Or you could take off easy and then plant it - again, to see what MPH is acheived on the run, and hence what potential ET the car is capable of.

Alternatively, you could take off hard and then either back off or brake before the finish line. Couple the first half track passes with the MPH acheived on the other runs and you can work out the opotimal run ET and TS. Then, go hard at the end of the day and get your 10second timeslip and get booted :D

/waves@Aaron :D:action-smiley-069::whistling:

Dam I went to one of these days before I brought my GTR and watched TWOOGLE & 2RISMO both ducking into the 10's yet weren't booted? I've been looking forward to running at such an event ever since yet sadly not paying $200 for 1 run :verymad:

That must have been quite a while ago and WSID's private days were much different back then. Now they have two types, ones like this SAU:NSW one (ie 11.00+ cars), and the private track hire days for ANDRA-teched cars (a handful of cars only).

YTS, easier for everyone including the volunteer organisers, if you join up beforehand ;)

http://www.skylinesaustralia.com/forums/topic/365434-s-a-u-n-s-w-club-membership-faq/

thanks i was planning on attending as a spectator and thought if i was gunna be there then i could just fill one out but this will do also cheers

Alternatively, you could take off hard and then either back off or brake before the finish line. Couple the first half track passes with the MPH acheived on the other runs and you can work out the opotimal run ET and TS. Then, go hard at the end of the day and get your 10second timeslip and get booted :D

/waves@Aaron :D:action-smiley-069::whistling:

Hehehehe, charlie, charlie charlie........

What car are you planning on running?

On a serious note, dont do the boot it too 1000" then brake hard. That is extremely dangerous, as we have found in past you have a good chance of turning the car around and punting it. I would prefer if you rolled off it at 1000" and cruised through the beams.

There are ways around this... you could break the beam (and start the timers) then take off and see what MPH you can get. This can indicate your potential ET on a perfect run. Or you could take off easy and then plant it - again, to see what MPH is acheived on the run, and hence what potential ET the car is capable of.

Alternatively, you could take off hard and then either back off or brake before the finish line. Couple the first half track passes with the MPH acheived on the other runs and you can work out the opotimal run ET and TS. Then, go hard at the end of the day and get your 10second timeslip and get booted

..

An ANDRA or WSID official will boot you for that sort of thing. If you break the beam and then hammer it or if you sandbag in the top end. Even if you go hard to half track and button off. I've been booted for that in the past but it DOES depend on who is the chief official on the day.

Ok entrant list is updated.. if you are missing and have paid more than 3 days ago pm me..

thanks guys

oh and before anyone asks spectators are not limited to 40 but 60.. pref will be given to entrants

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...