Jump to content
SAU Community

Recommended Posts

Hey all,

Looking around at engine oil pre-heaters for the Radical to cut down on the amount of hours on the engine for warming up, and help with general wear on cold start-up.

Anyone used them before? Looking at something like the Hot Head system: http://www.hotproductsengineering.com/?p=content&rp=hothead

Thoughts, opinions, advice etc all welcomed!

Cheers,

Dane

Link to comment
https://www.sau.com.au/forums/topic/365242-engine-pre-heaters/
Share on other sites

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

I would not bother with it Dane, every one that I have dealt with has been up to operating temp within 2~3 minutes of idling time, even less if it is moving with a bit of load on. The amount of time and energy spent setting one of these units up (with the attendant risks of leakage) is not worth the possible savings in rebuilds. That system also appears to only do the coolant, and not the oil, where the oil is the more important fluid to get to temp quickly.

Thanks for the advice Stephen. I'll ask the Radical guys how long it usually takes them to get sufficient oil temp and see what they say.

I must have linked the wrong one - I'm looking at oil pre-heaters rather than coolant as that's not too big of a concern. If it does indeed only take a few minutes then I won't worry about it.

None of the Radical guys (or any of the others) used them at Adelaide or Wakefield (where the temps got below zero overnight), all that it took in the mornings was start the car and let it run for a coupe of minutes. You are usually doing a walk around of the car at the time, checking for leaks or any other issues with the car.

Your stuck with your 30 hr rebuilds no matter what happens (unless you buzz the engine and get a yellow dash light) so whilst running the pre heater might save you somewhere around 30min of total run time over that period of time, if you are that concerned then you are going to have to manually move the car from the pits to dummy grid, shut down on the grid, etc. From what I have seen, the rebuild times might be on the short side for the engines in the Radicals, The engine in the Speads has done more than that with no lose of performance or cylinder pressures.

For that sort of time it's obviously not worth it. I was thinking that it may be more like 15 mins run time for each hour on track which would then be worthwhile.

30 hours is only for racing engines and as a precaution I think. I've heard of guys with 90 hours and no dramas so it's very conservative, but understandable with a warranty in place.

Well unless theres a difference in warm-up time between wet and dry sumps then it takes a lot longer than a few minutes. At Wakefield and Eastern Creek my Radical can take 10 to 15 minutes to get close to operating temp. I find I get water temp up way before oil temp. These Radical have massive oil coolers,,,without going out and measuring it I'm quessing it's about 300mm square.

I actually like the idea of running some sort of oil warmer,,,in fact I'm dry sumping my R33 and will look into such a devise. I don't know how much oil an SR3 dry sump system holds but my Prosport's wetty is 5.5 full,,,so lets say the SR3 has 8 litres,,,thats a lot of cold oil pumping through a cold DRY engine.

This may sound really stupid but what about making a tempory shroud around the tank and using a hair dryer,,,just a thought.

Cheers

Neil.

Why not just an electric heater element either within the oil tank or external around the tank, ie, a blanket.

Yea Ben,,,the nascar guy's run muliple small heating elements that screw into the dry sump tank (much like our standard heater sensor in our cats) but it take ages to heat up their 16 plus litres of oil,,,same with our V8 stupid cars. I've been told they spend like more than hour heating all liquids up to temp before hitting the start button.

You are right on track with the blanket one though,,,that would be my prefered option.

Andrew I no not of this nitrous bottle warmer thingy you speak of,,,got a link mate?.

Cheers

Neil.

I may not know Radicals but I do have an oil cooler setup on my S13 and I know it used to take 10-15mins to get oil temp until I fitted a thermostat that bypassed the cooler core until the temp reaches a certain point, cut oil warm up temps down drastically.

I've always thought about the concept of a an oil warmer/pre-heater but in reality it seemed to be a bit of a false economy as mentioned above. Just my opinion though and I'm not exactly highly experienced :D

Thanks for all the input guys.

Neil: I was thinking it was more around those times you've indicated, which may make it a worthwhile purchase. We'll see what sort of price the kit can be pieced together for and decide then whether it would make sense. Radical don;t really need to use them as they sit now because their track sessions are so compressed withing the day (20mins on, 20 mins off) so temps aren't an issue except for initial start up, but for regular track days and racing it would seem to make more sense.

Definitely looking at options with 240v as a requirement.

Dan: I wouldn't bother with a road based car as you can drive it around lightly to get temps up, and they never seemed to take all that long in the 180 with its oil cooler w/ thermostat. Radical tolerances are quite tight from what I'm aware, and the theres a lot of oil so it's more of a concern.

Dane, the tight arse in me thinks that a simple solution would be something like utilising the element out of an urn, like this;

http://www.boilexhotwater.com.au/birko_hotwaterurn.htm

It would be light and using a little enginuity you could mount it either under or depending on element style, within the oil tank. A neat little 240V plug affixed to the tank and just plug her on in when you arrive. :)

it's fairly simple for a dry sump. you get an oil pre-heater inside the oil tank, or the ones that wrap around the tank (some look like the nitrous bottle warmers some are more like a band or multiple bands around the bottom of the tank). all types work a bit differently and some better than others. the really small elements like a kettle type thing are not so good, I think the wrap around bands seem to work a bit quicker.

many of the brand name dry sump oil tanks come with heaters in them or on them as an option. hell you can buy a petersen dry sump tank with the heater on it for less than $200 from the US. keep the heater and toss or sell the tank. easy.

here's a pic of the band type ones.

post-3621-0-42511400-1306200086_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...