Jump to content
SAU Community

Recommended Posts

  • Replies 3.6k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

so, i decided yesterday arvo itd be a great idea to go for a casual drive in the hills and see some mud

_IGP8870.JPG

was about time to get it dirty. came down the hill alright, followed the ruts. Then the challenge got set....get back UP

first up was the "steamroller"

_IGP8893.JPG

made it look easy as piss, but then again he does have a locker

Gus tried it out in the "Atari" Vitara. Got a respectable distance up but wasnt getting any further

_IGP8900.JPG

My turn.......like driving an RB20, flat to the boards, take no prisoners

_IGP8912.JPG

_IGP8914.JPG

_IGP8915.JPG

_IGP8917.JPG

_IGP8919.JPG

wasnt goin to let this hill beat me, so rolled back for another go

VID_STILL06.JPG

VID_STILL07.JPG

VID_STILL08.JPG

VID_STILL09.JPG

VID_STILL10.JPG

gave up, as i was getting stuck in the very last bit of the rut and risked burying my diff in if i tried with any speed

then the next guy attacks it.....gets to the same spot, but not to be beaten, moves one more rut to the right....shit tonne slipperier. Keeps going back for bites, until this

_IGP8959.JPG

_IGP8961.JPG

pics dont show it well, but it was super steep and slick as. Used the first truck's winch, only to find the "cheap chinese copy" of a good winch wasnt sufficient...the end of the wire thats meant to be secured to the drum was just floating............so once tension was on it wouldnt pull

Time to try mine out

_IGP8992.JPG

3 hours later, god knows how many different pull angles, my winch rope bunched up and snagged, so we were destined to use only snatch straps to get out........bit of panel damage on the Maverick where it snagged on the tree on the low side, but we all got out

Now to clean all the "gorilla snot" off :rofl:

Scandy......think i need a new sig pic now :P

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...