Jump to content
SAU Community

Recommended Posts

Much cheaper than the kit they copied though. Much like their Geomaster knuckles... Speaking of which, if they retained standard ackerman angle, I'd be all over that shit. 50mm drop spindles FTMFW.

  • Replies 3.6k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I've just got rid of HICAS because the rear was out of control.... Was just doing whatever it felt like

Yea thats what i was going to suggest, bout to do the same on mine actually, rear is a little unpredictable at times.

just jap have a lock bar for i think $100, and looking at the DIY it doesnt look extremely hard to do.

Did you just chuck on a lock bar?

Driftworks have a nice kit that replaces the ball joints etc and all, bit costy though :/

yeah just a lock bar, it wasnt that hard to do, but you need a wheel alignment after, had some pretty epic toe in lol. I just adjusted it visually for the drive to the alignment place.

those that may not have Nene in their facebook here is one of her status updates a very grim warning

Janene Fulcher

At Elizabeth Centre when putting your children on the little rides. If an Old Lady comes up 2 u & starts poking her tongue out Sexually at your children Report her straight away. When my mum & I said we dont do that she kept going & i mean sexually poking her tongue out she then tried to get closer and closer to sienna & we are not exactly sure but it looked like she was going to pick her up.This happened to a friend of mine today! it is being treated as an attempted abduction by police. Janene

stage 2....pfffftttt

more car less camera Dave

Should be sufficient for the power I'm chasing. Don't need new springs and such with these either.

Hahahah, yeah... Now that I realise that money could've covered new wheel bearings, I do slightly regret it.

Slightly.

lol,

fitting up mine in a fortnight and cant decide to tune on flex or not. pros: it would be awesome and most likely make 310-320 ish. cons: that power would be useless, and if towing plans fall through for winton id have to take 400L with me. lol

those that may not have Nene in their facebook here is one of her status updates a very grim warning

yerp that my was daughter that Nene's talking about...Luckily the wife and mother in law were onto it!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Kinda glad I never got to this ..    https://www.facebook.com/groups/1483859159195077
    • @GTSBoy This method was able to get readings of -10 to -2, so it looks like its monitoring.  Now I need to figure out why the vacuum on the line provided isn't alternating with manifold pressure.  I went with 2 lines that an RB25 tuner recommended but I'll get a longer hose and try directly off the back of the manifold.  He may have been used to OEM intake setups while I have a DBW setup that removed the MAF and IACV.  
    • I work at a car detailing and tinting shop called Quark which gets all manner of German cars in usually (mainly due to a contract with Mercedes Benz Kita Osaka, BMW Nishinomiya and others) but every once in a while something special comes in, like a fully restored 1972 HS30 Nissan Fairlady 240ZG... The shop owner had immediately started applying film to the windows as soon as it was in the shop so the interior was completely covered in towels and plastic sheets. But I could get a few photos of the engine bay which was restored like new. Such an amazing car to see in pristine condition in Japan these days.  
    • Was going to say the car pulls up nicely everywhere, especially going into that last long right hander before the main straight. Looks like a lot of fun.
    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
×
×
  • Create New...