Jump to content
SAU Community

Recommended Posts

  • Replies 3.6k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Lols...

AK47, AR15, HK P90, Uzi, Barret M82A2, Walther PPK, Beretta M92F, Soviet RPG, Spud Gun, ? Car, Flintlock pistol, Lever action remington...

Sad. I know those all from memory but not the car

-D

shame on u about the car :whistling:

hey big shout out to the lad in the r33 satin black at gazzanats did very well me thinkls looked real nice tbh

and dunno how u guys feel about s15's but the grey one doing the drifting was phucin schmick and drifted like a pro very nice :worship:

So, the current power figures are in on my engine build...about 220rwkw at 8psi, should know more tomorrow after the tune has been touched up a bit more, and it should be in my possession :D

A lot more torque and response has been gained, we compared the dyno graphs from its 260rwkw tune from October 2009 to tonight's...almost identical except for peak power and boost coming on earlier now. If we run anything higher then 8psi (actuator pressure) the clutch starts slipping there is that much power being produced, dyno sheets to come tomorrow hopefully :D

just to spice up todays wasteland. pick one or many, lol , work warning, skimpy clothes

http://pasnation.pasmag.com/_262380143714126443917102298617001702162338njpg/photo/15255155/94594.html

Edited by Carbon 34
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Reading through the engine service manual their advice is do a cylinder balance test. Unplug one injector at a time and see if the idle drops a consistent RPM. You can also do this using a Consult cable which is easier. They also call for unplugging the power transistor, then with the engine off and the fuel rail unhooked from the manifold verifying that you have good fuel flow (even injection, no dripping/leaks, etc) when you twist the CAS by hand. Also verify the spark by pulling the spark plugs and allowing the plugs to ground and turning the CAS by hand. I would also start doing the sensor checks and idle valve checks in service manual. Make sure the MAF tests reasonably, the intake air regulator is sane, etc. You may have to get new spark plugs.
    • This sounds very old of me, however since buying the Tiguan shit box, my view on shit boxes have changed.
    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
×
×
  • Create New...