Jump to content
SAU Community

Recommended Posts

hi iam just about to pull the donk out of the 32 i know it can be dropped out the bottom as a whole 'and pulled out through the engine bay . from peoples expeirence witch way would be the easyer of the two i only have a trolly jack and an engine crane and the gear box has to come out aswel :cheers: cheers

Link to comment
https://www.sau.com.au/forums/topic/365631-r32-gtr-engine-removal/
Share on other sites

Unless you have a hoist, take it out the top after you remove the gearbox. With one jack and a couple of stands, you would never get the car body high enough to get the engine out from under it

when taking the engine out the top can i take it out with the box attatched ? what would the problem be doing it with the box on ?

Can be done with the box attached, just have to stuff around a bit to get the angles right to clear the tunnel and radiator support.

I'd highly recommend doing a google search to find the R32 service repair manual. It shows you step by step how to remove and re-install the motor aswell as other general service procedures.

Cheers,

Johno

i have a hoist in my garage... would it be best for me to drop it all out the bottom when the time comes for me to pull my motor? i was planing on taking it out the top, but if its easyer which im guessing it would be as there would be less to deal with when it comes to the Gearbox. dose all the suspension in the front end come out with it?

I once lifted the whole front of a GTR I had with the engine crane and slid the motor/subframe/gearbox assembly under it on the jack and bolted it up lol.

Its do-able either way but you prob wanna take it out the top way if you dont need to remove the box.

I pulled mine out through the top. Manifolds and turbos can stay on. Took me about half/to and hour to take it out, but i already had the box out. I had trouble with the RHF drive shaft and couldnt get it to pop out of the diff. Ended up cutting the inner CV boot clamps on that side, popping out the circlip and removing the shaft from the CV housing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
×
×
  • Create New...