Jump to content
SAU Community

Recommended Posts

Hey guys.

My car was doing something strange yesterday.

It started going lean and popping at idle, at normal operating temp, so I grabbed out my hand controller and my LC1 was telling me it was running about 18-20AFR!

Everywhere else was fine, under boost, cruising above 2000rpm etc, all fine, but as soon as the revs dropped below 2000rpm, coasting with no throttle and idle conditions caused the pop. Coasting down in gear under 2000rpm made it pop like mad. It's as if anything below 3mS of fuel became unstable, like I was running 1000cc injectors lol

It usually takes about 2.0mS of injector to get 12-14AFR at idle depending on ambient temp, but yesterday I needed 20% more fuel, 2.4mS gave me 14-15AFR with the occasional pop and 16-17.

Does anyone know what this sounds like? Keep in mind I havn't changed anything before, all I've done was install some LED angel lights, which weren't even on at the time.

dying fuel pump - unlikely, the pump is only 18 months old

blocked fuel filter - possibly

dirty injectors - maybe

bad batch of fuel - maybe, I filled up at Gull using their 98, which I had never done before!

Any ideas?

Link to comment
https://www.sau.com.au/forums/topic/365739-random-leaning-idle-and-coasting/
Share on other sites

Whats your setup - do you have an AFM?

What kind of voltage is the ECU reading?

Does the car do it consistantly since you first spotted this issue, or was it a once off?

And to clarify, do you mean specifically coasting down - or if it is actually sitting there at idle, will it stay at 18-20afr consistantly?

Whats your setup - do you have an AFM?

What kind of voltage is the ECU reading?

Does the car do it consistantly since you first spotted this issue, or was it a once off?

And to clarify, do you mean specifically coasting down - or if it is actually sitting there at idle, will it stay at 18-20afr consistantly?

Sorry not much info... haha

EMS Stinger - map sensored, no TPS.

Engine is a QR25DE+T

returnless fuel system, walbro pump, 440cc WRX injectors, stock everything else.

I'm not sure if it's a one off, I havn't started the car up today, just been sitting here studying all day - ill report back when I go for a drive later.

There's two situations that it does it, at idle, and coasting down in gear at low revs, both occur at low throttle, below 2000rpm.

it's odd because it's never done this before!

Does it sound like anything common?

I had this sample problem and couldn't fix it, would backfire badly when coming back onto the throttle and would pop at idle idling around 17:1 then would go back to 12:1

even had pete from nistune look at it and he wasn't sure of the cause

I had this sample problem and couldn't fix it, would backfire badly when coming back onto the throttle and would pop at idle idling around 17:1 then would go back to 12:1

even had pete from nistune look at it and he wasn't sure of the cause

That's exactly what my car is doing!

Aside from the current leaning problem, my car has always had an issue at around 1700rpm, you have to apply load very smoothly, otherwise it'll buck down and die, I've tried adding up to 40% more fuel at these points and it does nothing. As long as the car's had the EMS there, its had a problem at 1700rpm, but now since this new tank of fuel, it's developed this weird leaning condition.

Actually thinking of it now, the servo that I filled up at was a United. Up until last week I've avoided them because I didn't know they sold 98. But last week I filled up with their "98" for the first time. I'm leaning (pardon the pun) towards bad fuel...

Frankly, I wouldn't be worrying about running so lean at idle. It will not damage the engine at all, because there is virtually no load on the engine.

As for the popping, have to set up the EMS to shut off the injectors when the throttle closes (such as when you coast down, or change gears)?

Doesn't have an idle map as such, it's got a separate function for idle control, then I've just tuned the points around idle for 12-14 ish, then air temp and water temp correction values take over from there too, none of which I had changed before it started going wierd. Has no TPS.

Dont know what fuel pressure is doing, I dont have a fuel pressure gauge, if it starts going wierd again I'll look into it further...

Went fir a drive yesterday and it's all fine again...

Loose wires somewhere?

I cleaned up all the mess behind the head unit yesterday, coincidentally it stopped being wierd, but all I was doing was cable tieing things up, besides there's nothing behind there to alter fuel control...

Anyway thanks for your help bros!

Okay so the problem surfaced again today, and today was the same type of day. It's got something to do with overcast humid days. Not necessarily hot vs. cold, cos it runs fine at night and during a hot day. Maybe humidity plays a part?

i'm gonna do a fuel filter, run some injector cleaner through and install an air temp sensor and tune some air temp comp maps, see what that does.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If I had "perfect R33 GTR" kinda money I would have bought one of the crazy expensive low mileage HJA cars, but I am sadly not that wealthy. I already picked this car out of various Skylines for sale locally, most of which were worse in some way. Only a few cars were actually better but also more expensive. In terms of buying a motor locally, I at least have the option to inspect it myself and juding the seller as a person, and used or freshly rebuilt engines that some people sell are actually ok price-wise. I knew the car was going to require work, but shit piled up real fast and I haven't even driven 1000km yet as the turbo started oiling like a bitch within a few weeks after I got the car.   I assume it wasn't actually me who cracked it, though there is no way to know when that crack formed and if the previous owner even knew it was there. Buying another 05U Block can be a gamble, yeah, but the cheapest PRP cast block is like twice or more money-wise, and billet is 3 or 3 times as much. For now I am most likely just keeping the current engine, as a rebuild or engine swap isn't happening right now. But I am seriously considering buying a second engine and selling mine in return. Might be a sweet deal at the end.
    • Hi all. I need some help buying the correct size banjo bolts for my 2860 turbos. Because whoever installed them tore up the original part, I ordered new ones of this kind, because I just figured these were the most leak-resistant option as I already had trouble with a shitty braided line. I need to know the thread size of the smaller left hole, that is the turbo oil feed connection. I found out so far that the turbo oil inlet apparently has a 7/16"-24 thread, but I cannot find any listing or description of the thread size on this line. I do not have the original bolts. I tried using the bolts that were in the turbos (the ones that were mounted with the shitty braided line) but they sit very loosely so they can't be the right thread. Means either these bolts are the wrong ones (how do they fit the turbo then? no clue) or the wraparound-lines have a different thread than the turbo oil feed itself. Help is appreciated, asking Nissan directly is obviously not going to work.
    • EDIT: PSA to whoever stumbles upon this thread. It is in fact a crack in the block that caused this concern. Just letting you know. In my case, a few cm long hairline crack going horizontally above the turbo oil feed. Classic RB shit I guess
    • Might as well pop in some cams, head gasket, head studs, and a flex sensor. Full send.
×
×
  • Create New...