Jump to content
SAU Community

Recommended Posts

  • Replies 144
  • Created
  • Last Reply

Top Posters In This Topic

I'll be there with StageIan, but unfortunately he's still not able to drive his own car after his bike crash.

Ouch! :down:

Don't know Ian; but I don't like hearing about fellow bike riders being injured; feel better mate.

Cheers, Dale.

Edited by Daleo

Got all volunteers you need? Did a cake get organised ?

Thanks for your Qs ^ ^ ^ keeping us on our toes :thumbsup:

After the meeting 28/8/11, we'll be

* assigning jobs (if anyone is still offering to help - thanks in advance)

* using photos to get quotes for a Stagea Cake

* finalising logistics with Top Secret Imports

* giving feedback to Jason Round at Performance Imports

* giving feedback to the SAU Execs on 7/9/11 Meeting

* posting up Nick's threads in the Events sections of each state Re: 15th Anniversary.

OK everyone, this big meet is on tonight!!! Who's coming along?

Like I said, they're supporting us, so let's support them. There'll be a BBQ going, plenty of give-aways (both from Top Secret Imports, and from Project D Drift School, as well as others), and lots of cars to look at. It should be huge!

OK everyone, this big meet is on tonight!!! Who's coming along?

Like I said, they're supporting us, so let's support them. There'll be a BBQ going, plenty of give-aways (both from Top Secret Imports, and from Project D Drift School, as well as others), and lots of cars to look at. It should be huge!

take some pic's :)

OK everyone, this big meet is on tonight!!! Who's coming along?

Like I said, they're supporting us, so let's support them. There'll be a BBQ going, plenty of give-aways (both from Top Secret Imports, and from Project D Drift School, as well as others), and lots of cars to look at. It should be huge!

will be there.

The police were fine, they'd been pre-warned that the event was happening. They just wanted everyone to stay off the road, which is fair enough.

How long were you there, Iain?

ahhh i wasnt sure, we didnt want to take any risks with our highly defectable volvo station wagons lol

was there for maybe 45 mins. didnt see you there, and i realised i dont have your number either!

I enjoyed it - good to see a range of cars.

Was waiting for there to be a rockclimber sized hole in the side of the building! happy.gif

Looks like a good place to start for the Main game- the 15Th Anniversary!

Yep, would have been kinda funny to watch the rock climber or the Commodore roll off into the building (as long as no-one was injured in the process).

Was good to catch up with Alex, Craig and Ryan, and I'm pretty sure Ian had a good time too. It would have been good for his cabin fever after being stuck inside the house most of the past two months since his bike crash.

Nice of Craig to volunteer helping Ian with the mods for Ian's little red wagon too! :P

Alright peoples, I'm in the process of doing the proper thread for the cruise, and once it's all sorted and ready to go I'll post links to it here and in each of the state Events threads for Queensland, Canberra and Victoria too. So keep your eyes open for it!

  • 2 weeks later...
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
×
×
  • Create New...