Jump to content
SAU Community

Recommended Posts

sonnyQ,

Here's what I'm talking about lol

img1371si.jpg

img1372bx.jpg

thanks for that man. I was looking at it the other day thinking it would probably need to be cut.

still trying to make time to fit this unfort. Think ill have to go with screws and tape because I will be too lazy to put it back on if something happens.

Charles! Mine is falling off a bit around the corners on both sides :(

Are they staples in that pic above? Will a staple gun pierce through the front bar? I wouldn't have thought so >_<

Did you clean the bottom of your front bar thoroughly before attaching?

It's not a staple gun lol, just normal staples, so I can hold the cut together.

The only thing that's holding onto my lip is some industrial double sided tap.

Charles! Mine is falling off a bit around the corners on both sides :(

Are they staples in that pic above? Will a staple gun pierce through the front bar? I wouldn't have thought so pinch.gif

I used wax and grease remover before putting my double sided tape. Might be worth a try.

I'm wondering what would happen if I put some sort of wax on the lip lol, I want it shinier :D

Black boot polish on the lip to make it shiney, I put it on the garnish on the bottom of my R32's rear bar when I clean my car. Stays blacker than the ace of spades for months.

Black boot polish on the lip to make it shiney, I put it on the garnish on the bottom of my R32's rear bar when I clean my car. Stays blacker than the ace of spades for months.

Haha sweeet! Gonna try that :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
×
×
  • Create New...