Jump to content
SAU Community

Recommended Posts

havent updated for a very long time.

cars painted

cars on the road

car goes like a ripper

went to a dyno day today pulled 288rwhp on stock turbos on 15psi

some recent pics here

DSCF4055.jpg

DSCF4018.jpg

DSCF4015.jpg

DSCF4004.jpg

DSCF4002.jpg

  • Replies 61
  • Created
  • Last Reply

Top Posters In This Topic

Its a faaaarkin awesome build dude not knocking it for a second but a 2J has 500cc more so personally i think it can do alot more than a 1J sure it could probably go toe to toe on a dyno in a HP shootout but that half litre more just gives you torque more turbo response which may not look that different on a dyno but the drive would be very different

  • 4 weeks later...
  • 2 weeks later...
  • 3 weeks later...
  • 3 weeks later...

awesome work mate love it. want to know how you made the engine mounts as im looking to do the same to my r33. i already have motor as i own a jzz30 soarer as well but want to swap motors any info would be great

i have found mounts for your s series nissan crossmembers and from memory the s14 crossmember are interchangeable with r33 not 100% sure though and as for the sumps im not to sure about that will have to look into it

you need a front sump yes. i have a few rear sumps here and they are useless i cant even sell them!!

i made my own engine mounts and run the r32 cross member and rubbers.

just sit your engine in the engine bay where you want it and fab up the mounts yourself.

get the motor as low as possible and as far back as possible.

pretty simple if you are handy with the tools

  • 4 weeks later...

so the engine was down on compression and the valve stem seals were causing a lot of smoke

so i got stuck in and built a new 1jz up for it. took me 2 weeks to build it myself and get it in and running.

got the urge for more power so i went with a t66 turbo, and a few little other supporting mods

still runnning a stock ecu with safc2 controller

finished with a total of 413 rwhp 308rwkw at 24psi

here are some pics

2012-06-02201337.jpg

2012-05-27105830.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...