Jump to content
SAU Community

Recommended Posts

I agree. I love the black leather & electric seats, but the switch gears digs into my thigh a bit on longer trips.

There is a Nissan service bulletin that covers a (potential) fix for this - I posted them on m35.info forum - but I've still not bothered to try it.

  • 4 years later...

Bit of an old thread, but does anyone still do the English conversion for the stereo ? Have just imported an 04 ARX, replaced the suspension with mca x-r's and bushes are up next before it goes for a blue slip.. But the stereo is the next priority after that.. I'm in Sydney if that is relevant.

Many thanks in advance

Ps has anyone been able to get the maps working for Australia ? Not overly important, but curious all the same

I've never seen that second pocket! Mine has a weird Panasonic DVD drive in there for the GPS system.. that'll get ripped out eventually :P

I got it from yahoo auctions in Japan. Yours may have had the screen from factory as mine had the dvd rom in that area.

Problems

 

Turbo Failure:

If the oil lines get blocked, yes your turbo will fail. Clean or replace your lines and your good to go. Drilling your banjo's to 3mm will just cause excessive flow  and encourage oil to leak out the turbine oil ring causing smoke.

The main failure is the ceramic turbine breaking off the turbine shaft. Oil flow is not related to this. The cause is directly related to turbine speed. If you want the OEM turbo charger to last, don't put a dump pipe or exhaust on it, Don't increase boost otherwise it will fail eventually.

 

Rear Shocks:

Upper Mounts will rip out of the car when performance shocks are installed or even with OEM. The top hats rust out due to the stupid design

 

Rust:

They like to rust in the lower kick panel, window frames, gearbox mount point.

 

Air Flow Meters:

The OEM Airflow meters blow continuously. Best by a AFM off ScottyM35 as these are the only ones Ive seen last.. better than getting stuck..buy one straight up

 

Interior:

The interior is just ugly, it squeaks and creaks  

 

Engine:

The engine is capable of serious power and great response. Be warned the head studs are cheese and will leak/lift with almost any detonation. The OEM injectors run out of flow easily so be wary of an M35 Series 1 with an exhaust but no other supporting fueling mods, it will most likely already have a broken piston. Every M35 series one I have compression tested have had at least one piston broken(greater than 10% compression variance). Rocker cover Gaskets go hard and leak. Electronic throttle isn't the most reliable. The coil packs don't like Adelaide 48 degree heat.  

 

Transmission:

This will start slipping on mid throttle changes on the OEM setup when boost is increased and destroy itself. Can only be patched with a shift kit

 

Brakes:

The brakes are hugely undersized and will wrap and crack with any spirited driving.

 

Electric Windows:

The drivers window motor will eventually strip the inner cog. OEM window motors are expensive.

 

Rear Sub Frame:

They can crack at the top of the inverted U. You can't tow

 

Electrical:

The Battery Control Modules are almost all been water damaged at some stage due to blocked drain holes. The rams in the front seats are prone to setting off intermittent Air bag faults. Centre pop up screen is useless, even when converted to English   

 

Stereo:

The original Bose system sounds good, changing it requires a bandwidth adaptor(PAC-OEM2). People charge insane amounts for a Double din fascia.

 

 

Summary:

Buy the series 2, 2wd version with the 3.5ltr if you don't plan on modding the series 1 turbo. If you are looking at going down the turbo path, don't modify it unless you are (a) very patient and capable of your own work or (b) are willing to spend big money with a workshop who actually knows these cars. Buy the car will all the options that you want already...ie AXIS, leather, sunroofs, radar cruise etc. Don't by a turbo version without completing a compression test.

 

 

Matt

 

Edited by BoostdR
8 hours ago, BoostdR said:

Problems

 

Turbo Failure:

If the oil lines get blocked, yes your turbo will fail. Clean or replace your lines and your good to go. Drilling your banjo's to 3mm will just cause excessive flow  and encourage oil to leak out the turbine oil ring causing smoke.

The main failure is the ceramic turbine breaking off the turbine shaft. Oil flow is not related to this. The cause is directly related to turbine speed. If you want the OEM turbo charger to last, don't put a dump pipe or exhaust on it, Don't increase boost otherwise it will fail eventually.

 

Rear Shocks:

Upper Mounts will rip out of the car when performance shocks are installed or even with OEM. The top hats rust out due to the stupid design

 

Rust:

They like to rust in the lower kick panel, window frames, gearbox mount point.

 

Air Flow Meters:

The OEM Airflow meters blow continuously. Best by a AFM off ScottyM35 as these are the only ones Ive seen last.. better than getting stuck..buy one straight up

 

Interior:

The interior is just ugly, it squeaks and creaks  

 

Engine:

The engine is capable of serious power and great response. Be warned the head studs are cheese and will leak/lift with almost any detonation. The OEM injectors run out of flow easily so be wary of an M35 Series 1 with an exhaust but no other supporting fueling mods, it will most likely already have a broken piston. Every M35 series one I have compression tested have had at least one piston broken(greater than 10% compression variance). Rocker cover Gaskets go hard and leak. Electronic throttle isn't the most reliable. The coil packs don't like Adelaide 48 degree heat.  

 

Transmission:

This will start slipping on mid throttle changes on the OEM setup when boost is increased and destroy itself. Can only be patched with a shift kit

 

Brakes:

The brakes are hugely undersized and will wrap and crack with any spirited driving.

 

Electric Windows:

The drivers window motor will eventually strip the inner cog. OEM window motors are expensive.

 

Rear Sub Frame:

They can crack at the top of the inverted U. You can't tow

 

Electrical:

The Battery Control Modules are almost all been water damaged at some stage due to blocked drain holes. The rams in the front seats are prone to setting off intermittent Air bag faults. Centre pop up screen is useless, even when converted to English   

 

Stereo:

The original Bose system sounds good, changing it requires a bandwidth adaptor(PAC-OEM2). People charge insane amounts for a Double din fascia.

 

 

Summary:

Buy the series 2, 2wd version with the 3.5ltr if you don't plan on modding the series 1 turbo. If you are looking at going down the turbo path, don't modify it unless you are (a) very patient and capable of your own work or (b) are willing to spend big money with a workshop who actually knows these cars. Buy the car will all the options that you want already...ie AXIS, leather, sunroofs, radar cruise etc. Don't by a turbo version without completing a compression test.

 

 

Matt

 

Reading you post Matt and i don't want a stagea anymore :).

In other news;

No other car ever built in the history of motoring has ever had any kind of reliability issue.

So probably just go & buy one of those.

Maybe a Jeep; they seem quite good.

  • Like 2

Stock is fine, especially for what I have found so far in these cars... Compared to an "Aussie" made equivalent it's a stark difference in what is considered stock.. And largely where it's tempting to have fun and go all out, I am personally trying to keep it "stock"....

Where OEM parts are available, I would largely go for them, but at the same time, if it's cheaper to put something potentially better on, I know what I would rather do...

On 7/4/2016 at 10:32 AM, West said:

Reading you post Matt and i don't want a stagea anymore :).

So get a PM35.

No turbo to worry about

Different AFM (seems much more reliable)

Nicer interior

Common engine

Updated transmission

 

Really, the only downside to the 3.5L is that there is no turbo.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...