Jump to content
SAU Community

Recommended Posts

Hi guys just an update

Came back from the workshop and he said that it was likely the actuator on the turbo that is stuffed overboosting the turbo causing it to whistle.

I advised him at first that it maybe the gasket between the manifold and Turbo so he opened the bonnet and reved it. He said if it was a leak he would have heard it.

So we then went for a spin and at times the boost would spike to around 13-14 psi and make that whistling noise. When the boost only when to 10 psi it wouldnt.

So his diagnosis was that since he had removed the boost controller and put the stock bits in and it was overboosting that it is probably the actuator that is stuffed causing the turbo to overboost and make that noise.

Opinions please? Sounds plausible? Should I get another workshop to look at it before I decide to shell out for a new turbo.'as he said I just may as well buy a new turbo.

Any help much appreciated :)

I would say hes probably telling you the truth. I've unfortunately got an exhaust leak from my rear turbo and the sound doesn't come or go, it's always there. You can hear the 'airy' sound on decel and it runs like a bucket of shit. Have him finish of his work and before you pay the bill ask him to come for a quick lap to see if it's still doing it.

Hi guys just an update

Came back from the workshop and he said that it was likely the actuator on the turbo that is stuffed overboosting the turbo causing it to whistle.

I advised him at first that it maybe the gasket between the manifold and Turbo so he opened the bonnet and reved it. He said if it was a leak he would have heard it.

So we then went for a spin and at times the boost would spike to around 13-14 psi and make that whistling noise. When the boost only when to 10 psi it wouldnt.

So his diagnosis was that since he had removed the boost controller and put the stock bits in and it was overboosting that it is probably the actuator that is stuffed causing the turbo to overboost and make that noise.

Opinions please? Sounds plausible? Should I get another workshop to look at it before I decide to shell out for a new turbo.'as he said I just may as well buy a new turbo.

Any help much appreciated :)

I doubt you need a new turbo.. more like the actuator hasnt been put on properly or you have a leaking hose, why not get in there yourself and eliminate all these possible causes, source a second hand acutator and try it yourself

i leaking hose would give you overboost, cost to replace =zip

get a bright light in there and look for any soot gather around the gaskets which = leaking gasket

make sure you dont have some garrett highflow, i never knew myself until i was told,

you dont have a cheap split dump pipe do you?

Just an update guys!

So after 2 weeks of being told the noise is my boost controller, then my turbo , then my actuator and dismissing that it can't posssibly be the gasket between the turbo and manifold, I dropped off the car to Rob at Sabbiddin Automotive to get the car checked out. I've had my car for their for mechanical work in the past and respect his professionalism.

I just received a call from Rob just then and hey prestoooo...It's the gasket between the turbo and manifold, and that there's a bit of shoddy work from the previous work :rolleyes:

Regardless I'll be eventually getting a new turbo soon, but didn't appreciate the advice from the previous workshop even after telling him what was the problem.

So just a shout out to everyone that helped and especially Daniel from Elite Racing :cheers:

I won't publicly name the workshop as that isn't appropriate & allowed and to a certain extent everyone makes mistakes, but I will say this workshop is in the South-eastern suburbs of Melbourne and is a workshop referred onto by one of the top Tuners in Melbourne that is regarded on this forum.

:thanks: to the SAU Community :action-smiley-069:

Just an update guys!

So after 2 weeks of being told the noise is my boost controller, then my turbo , then my actuator and dismissing that it can't posssibly be the gasket between the turbo and manifold, I dropped off the car to Rob at Sabbiddin Automotive to get the car checked out. I've had my car for their for mechanical work in the past and respect his professionalism.

I just received a call from Rob just then and hey prestoooo...It's the gasket between the turbo and manifold, and that there's a bit of shoddy work from the previous work :rolleyes:

Regardless I'll be eventually getting a new turbo soon, but didn't appreciate the advice from the previous workshop even after telling him what was the problem.

So just a shout out to everyone that helped and especially Daniel from Elite Racing :cheers:

I won't publicly name the workshop as that isn't appropriate & allowed and to a certain extent everyone makes mistakes, but I will say this workshop is in the South-eastern suburbs of Melbourne and is a workshop referred onto by one of the top Tuners in Melbourne that is regarded on this forum.

:thanks: to the SAU Community :action-smiley-069:

Glad to help. It's good that you found someone to sort it out for you. I was going to suggest someone when you asked but thought again about it. I was absolutely certain it was going to be that gasket so it is a good thing you persisted with it or you end up like every other poor bastard around.....even poorer and still without a fixed car.

Rule #2 is: If it smells like shit, feels like shit and tastes like shit....it's most likely not going to be a cheese sandwich

Thanks guys :cheers:

Just picked up the car and it feels great again. Rob said some bolts were missing, some bolts not tight, hoses weren't in properly ahhh i just had to laugh.

Now its time to save up for some ID 1000 injectors and a Hypgear turbo :thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...