Jump to content
SAU Community

Recommended Posts

  • Replies 99
  • Created
  • Last Reply

Top Posters In This Topic

Yeah me too man, got the shed booked for powercruise in September so that will be the cars real shake down for the car. organised a new cooler for the car and a OS twin plate..

  • 2 weeks later...
  • 1 month later...

hey guys bit of an update. trying to fix all the little half arse jobs that the car has had over the last couple of months. So ive started on new intercooler piping and air intakes, mounted the intercooler properly, new tial bov and fitted the wide band sensor in a different location. Kinda ran out of money with the dyno tunig so no real numbers to talk of until everything is fixed.

couple of pics

post-11029-0-97714800-1337691790_thumb.jpg

post-11029-0-15388000-1337691799_thumb.jpg

post-11029-0-78108900-1337691807_thumb.jpg

post-11029-0-53419600-1337691816_thumb.jpg

post-11029-0-41439000-1337691831_thumb.jpg

post-11029-0-08772200-1337691840_thumb.jpg

Love it, my mate had two 2835's on his 26 with 0.6X rears and it was insane.

Yours will be like 4.5K Mmm what's that noise then 5K omg something is happening then bam 6K wheel spin/rev limiter and warp speed. It will be epic good luck mate keen to see the finished product.

  • 2 weeks later...

started on my catch can breather system last night..

2x -10 breathers from the valve covers

1x -10 breather from the oil filler cap

1x -12 drain back to the sump

1x -6 back to the manifold

1x -8 flapping in the breeze

post-11029-0-90513300-1338506335_thumb.jpg

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...