Jump to content
SAU Community

Recommended Posts

  • Replies 73
  • Created
  • Last Reply

Top Posters In This Topic

Not exactly minutes, but not too long if you know what your doing, ill do a write up, ill call nissan now and see if i can get the gaskets today, so the standard gaskets are better than the ebay ones yeah.

From what I can see you have major issues I may be able to help with a few things here:

tcs light / slip light stays on - This is common on R34's and is usually solved by putting in new coil packs (jjr, yellow jackets, splifires) this is what I did to solve this in my car.

Leaking gasket of unknown origin - take the heat shield off the turbo and grab a length garden hose put it to your ear and put the other end to the manifolds (turbo and exhaust) check it a section at a time, this is the easiest way to see what is blown (I had a similar problem with mine it was my turbo manifold gasket - replaced with ultra copper gasket maker and it has no problems now).

Boost gauge / controller issues - buy an electronic boost gauge / controller that is known to be quallity manufactured IE: Apexi AVC-R (cheaping out on these cars will really break the bank later on down the line)

If your car is still having issues with these things after this go see a mechanic that has skills with skylines don't take it to joe blogs down the road as they tend to have very specific issues.

also check for perished hoses on the throttle body ( I found 2 on mine and it was in damn near immaculate nic everywhere else)

Edited by RandomHero83

Hey randomhero, well I was told that aswell but the car isnt missfiring or anything? and usually if its the coil packs doesnt the check engine light turn on or anything? well I put the new o2 sensor in and the fuel economy is awsome now, 400kms to the tank thats double of what i was getting :D, as for the idle, I cleaned out the afm with afm cleaner, went for a nice spirited drive and its back on 950rpm so I'm happy, hopefully if its not raining tomorrow I will be changing the turbo gaskets, as for the boost guages I found the problem, the T peice had blown a hole in the middle and was leaking there, i havent ever seen that happen before but yeah wierd haha lol, do you think its time I can put my front mount intercooler on? would I be expecting any power gains from a front mount? also what are the best brake pads that make minimal brake dust? the ones that are on there now are just horrible the whole car turns black after a few stops.

One more thing, is it normal for the rear bar to go black from the exhaust? is that just because its running rich?

Thanks everyone for your help.

Hey guys what do use think is better just geniuine nissan turbo gaskets or permaseal mls-r gaskets? ive read great comments about both, soon ill be running around 12psi like i used to untill these problems arised, please let me know asap please, thanks.

Edited by MrRx7s3

Hey thanks jez I've ordered the permaseal ones and I should receive and fit them tomorrow hopefully, the car still smells really rich from the exhaust, what else could be causing such a rich mixture.

Also I noticed today that when the car is idleing its at around 900-950rpm, when I turn the parker lights on it rises around 150rpm and then when I turn the full head lights on its only raised around 50-100rpm.

Also does anyone know about the black gunk on my rear bar and exhaust that I mentioned earlier.

Thanks to everyone for your help, I really do appreciate it greatly, thanks.

Edited by MrRx7s3

Are you selling the O2 sensors? Im only getting 300K per tank.

I had a similar problem..

My link my post

at the end my AFM was causing the problems, but after cleaning the AAC the idle is much better

Aac cleaning

Hey guys I installed a E-Boost 1 in my car and I'm having some problems, no matter how I set it the boost is never right, it keeps on fluctuating, say on setting 2 I put it to run 10psi it will boost up at 3000rpm spike to 14 and then at 4500rpm just kark it and go to 5psi, its not cutting out or anything just loosing the boost hard, I've played with the sensitivity and gate open pressure and it just wont work right, I'm using iradium plugs 1.1mm gap, currant mods are 3" cat back exhaust, pod filter, I'm getting a FMIC installed this week but i doubt that that will help with the boost, any help is much appreciated, thanks.

Hey guys, well I finally decided to degrease my engine bay, and I thought the coilpack cover should be sealed, well I guess not, and its been missfiring so i just left the car on to let it dry off because my aircompressor is at work and after about 20 minutes of driving/idleing it was ok, now it started again mainly on boost but sometimes on idle, have I killed my coil packs? or should i just wait untill i get my aircompressor back and dry it up? let me know asap please, thanks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...