Jump to content
SAU Community

Recommended Posts

Did back to back dyno testing at Boostworx. Eflex made less power then normal 98. The liberty e85 made 15-20kw more. Eflex isn't e85 its e70-e85 as it says on the pump.

While I dont doubt your figures this is totally the opposite of the testing I have carried out for our own vehicles.

However I have never tested 'Liberty' E85 only the United CSR Sarina manufactured blend, I think you may be getting confused with United. If there is a Liberty selling here let me know and I will test it.

E-Flex is a much maligned fuel. As stated on the brochure on the Caltex servo counter this fuel WILL contain as little as E70 in some circumstances, and yes it has when I test it (71% concentration is the lowest measured directly). This gives the fuel an effective tuning RON (my calcs here, not measuring on an octane machine) of around 110 - 112 RON. It is also highly oxygenated which means that it is capable of delivering good combustion energy - significantly higher than that of E85. I do not know why Boostworx have found it makes less power than 98 octane fuel as on a typical 200rwkw turbocharged engine (on a Mainline dyno) we can normally extract in the order of 10% - 14% additional power and torque swapping from 98 to E-Flex. The tuning technique required does however require some thinking outside of the square with some engines.

Yes, my family hack is a Flex-Fuel setup EVO X, and yes it runs on either 98, or more preferably (as it makes a ton more power and costs $40 a week to run) E-Flex :)

CSR Sarina E85 is a little more pure for the racers measuring at around 88% Ethanol in most cases and can make a tad more power than E-Flex (not a great deal in it). We run the United CSR blend in - all - our Willall Racing track and drag cars, but maybe we are missing something? :pirate:

Link to comment
https://www.sau.com.au/forums/topic/372229-e85-fuel/#findComment-5936774
Share on other sites

Yup, I meant United not liberty on Tapleys Hill Rd >_<

Not to sure whay exactly it made less power then 98, wasn't by much though 230rwkw vs 226rwkw. Could have been a bad batch of fuel or it could have been down to tuning technique.

But as I said, and you stated above. The United E85 will make more power then eflex as its a more pure blend. Considering the United E85 is as cheap as eflex I know what i'll be buying all day every day.

Link to comment
https://www.sau.com.au/forums/topic/372229-e85-fuel/#findComment-5937061
Share on other sites

Cheers guys.

Considering runnoing the evo on it.

A few blokes from other states have been doing it for awhile.

Have seen back to back dyno results and have been impressed...

As far as 'stuffing things up' i havent heard of much. what are the risks?

Link to comment
https://www.sau.com.au/forums/topic/372229-e85-fuel/#findComment-5937191
Share on other sites

Here, here, good to see your still a champion for the good stuff Mr Donnon.

I say go for it, Eflex is more than capable even at 70%.

I use the United E85, but have no problems at all throwing in Eflex,

United's wins on my seat of the paints dyno.

Recently tuned a S15 SR to 1.85bar on E85 running a disco with all the bolt on's, got a good compromise mapping both fuels, hasnt had it's power measured yet, but far out it fly's, high 200's at a guess.

Link to comment
https://www.sau.com.au/forums/topic/372229-e85-fuel/#findComment-5937549
Share on other sites

Here, here, good to see your still a champion for the good stuff Mr Donnon.

I say go for it, Eflex is more than capable even at 70%.

I use the United E85, but have no problems at all throwing in Eflex,

United's wins on my seat of the paints dyno.

Recently tuned a S15 SR to 1.85bar on E85 running a disco with all the bolt on's, got a good compromise mapping both fuels, hasnt had it's power measured yet, but far out it fly's, high 200's at a guess.

.82 rear or .64? I've got the .64 making 240rwkw at 20psi dropping off to 16psi (small wastegate). If you have .82 is there much lag? would be keen to see power graphs as thinking of changing rear housings on mine.

Link to comment
https://www.sau.com.au/forums/topic/372229-e85-fuel/#findComment-5937604
Share on other sites

I'm amazed at the attitude towards E70 vs E85............I think peeps are forgetting that the fuel alone won't give you the kind of power you're looking for.

In fact, 98 pump fuel will burn much better (combust) than the higher octane Ethanol.........the stuff just doesn't burn!!!

What the Ethanol allows you to do is turn up the boost and and throw more ignition timing at it, hence where the additional power comes from................the stuff doesn't know the meaning of the word Detonation!!!

Link to comment
https://www.sau.com.au/forums/topic/372229-e85-fuel/#findComment-5938071
Share on other sites

people still hate on e85 haha, i have been running e85 for 3 years thanks to adrian, never had a issue pushing awesome power! it really is power for nothing compared to what some people spend chasing small gains, as well as safer. as for blends tryed nearly all varietys and never had issues.

Link to comment
https://www.sau.com.au/forums/topic/372229-e85-fuel/#findComment-5938162
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...